FAXMODEM(8C)FAXMODEM(8C)NAMEfaxmodem - dynamically add a modem to a HylaFAX server
system
SYNOPSIS
/usr/contrib/bin/faxmodem [ -q queue-dir ] [ -c capabili-
ties ] [ -p ] [ -P ] [ -u priority ] modem
DESCRIPTIONfaxmodem sends a message to the HylaFAX queuer process
faxq(8C) telling it that the specified modem is ready for
use and informing it about its fax-related capabilities.
This is the mechanism by which modems are added in a send-
only configuration. Once a modem has been configured its
status can be reconfigured using the faxstate(8C) program.
faxmodem can also be used to alter the capabilities and
usage priority of a previously configured modem.
The specified modem is either the terminal device name
where the modem is attached or a HylaFAX device identifier
(see config(5F) for information on device identifiers).
Device names may be given without a leading directory
pathname; e.g. ttyf2 instead of /dev/ttyf2.
To figure out the capabilities of a modem either use the
probemodem(8C) script or manually communicate with the
modem. For a Class 2 modem the capabilities are given in
the response to the ``AT+FDCC=?'' query command and for a
Class 2.0 modem the ``AT+FCC=?'' command. To check if a
modem is capable of polled retrieval of documents use
``AT+FSP=?'' for a Class 2.0 modem or ``AT+FSPL=?'' for a
Class 2 modem; if ``1'' is indicated in the response then
the modem supports polling. For example,
hyla% cu -l ttyf2
Connected
at+fclass=2.0
OK
at+fcc=?
(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)
OK
at+fsp=?
(0,1)
OK
In this case the modem would be added using the command:
/usr/contrib/bin/faxmodem -c '(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)' ttyf2
(by default polling is assumed to be supported).
Class 1 modems require a different technique. The host
implements most of the fax protocol so all that is needed
is to identify the possible signalling rates the modem
supports for transmitting; this is done with the
``AT+FTM=?'' command. For example,
Oct 27, 1995 1
FAXMODEM(8C)FAXMODEM(8C)
hyla% cu -l ttyf2
Connected
at+fclass=1
OK
at+ftm=?
24,48,72,73,74,96,97,98,121,122,145,146
OK
In this case the modem supports 2400, 4800, 7200, 9600,
12200, and 14400 bps signalling rates so the modem would
be added using:
/usr/contrib/bin/faxmodem -c '(0,1),(0-5),(0-2),(0-2),(0,1),0,0,(0-7)' ttyf2
OPTIONS
The following options are available:
-c Specify the fax capabilities using the syntax
defined by the ``Class 2'' specification:
``(vr),(br),(wd),(ln),(df),(ec),(bf),(st)''.
where, vr specifies vertical resolution, br
specifies bit rate, wd specifies page width, ln
specifies page length, df specifies data com-
pression, ec specifies error correction, bf
specifies binary file transfer, and st specifies
scan time/line; and each of the above specifica-
tions is a range or list of numbers that defines
the exact capabilities of the modem. For exam-
ple, the default capabilities are
``(0,1),(0-3),(0-4),(0-2),(0),(0),(0),(0-7)''
which specifies the modem is capable of sending
and receiving both low and high resolution fac-
simile with a variety of page sizes; supports
signalling rates 0-3 (2400 bps through 9600
bps); supports only 1D-encoded data compression;
and does not support error correction or binary
file transfer. A modem's ability to support
polled retrieval of facsimile is specified sepa-
rately with the -p and -P options.
-p Specify the modem is not capable of polling for
remote documents.
-P Specify the modem is capable of polling for
remote documents (default).
-q dir Use a spooling area other than /var/spool/fax.
-u priority
Assign the specified priority to the modem when
scheduling it for outbound use. Modem priori-
ties are numbers in the range [0..255] with
lower numbers meaning higher priority. Modems
are initially assigned priority 255.
Oct 27, 1995 2
FAXMODEM(8C)FAXMODEM(8C)FILES
/var/spool/fax default spooling area
/var/spool/fax/FIFO fifo for contacting faxq
Consult hylafax-server(5F) for a complete discussion of
the structure and content of the spooling area.
SEE ALSOhylafax-server(5F), faxgetty(8C), faxq(8C).
Oct 27, 1995 3