EM(4) BSD Kernel Interfaces Manual EM(4)NAMEem — Intel(R) PRO/1000 Gigabit Ethernet adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device ig_hal
device em
Alternatively, to load the driver as a module at boot time, place the
following lines in loader.conf(5):
ig_hal_load="YES"
if_em_load="YES"
DESCRIPTION
The em driver provides support for PCI Gigabit Ethernet adapters based on
the Intel 82540, 82541ER, 82541PI, 82542, 82543, 82544, 82545, 82546,
82546EB, 82546GB, 82547, 82571, 81572, 82573, and 82574 Ethernet con‐
troller chips. The driver supports Transmit/Receive checksum offload and
Jumbo Frames on all but 82542-based adapters. For further hardware
information, see the README included with the driver.
For questions related to hardware requirements, refer to the documenta‐
tion supplied with your Intel PRO/1000 adapter. All hardware require‐
ments listed apply to use with DragonFly.
Support for Jumbo Frames is provided via the interface MTU setting.
Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility con‐
figures the adapter to receive and transmit Jumbo Frames. The maximum
MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. The em driver supports the following
media types:
autoselect Enables auto-negotiation for speed and duplex.
10baseT/UTP Sets 10Mbps operation. Use the mediaopt option to select
full-duplex mode.
100baseTX Sets 100Mbps operation. Use the mediaopt option to select
full-duplex mode.
1000baseSX Sets 1000Mbps operation. Only full-duplex mode is supported
at this speed.
1000baseT Sets 1000Mbps operation. Only full-duplex mode is supported
at this speed.
The em driver supports the following media options:
full-duplex Forces full-duplex operation
half-duplex Forces half-duplex operation.
Only use mediaopt to set the driver to full-duplex. If mediaopt is not
specified, the driver defaults to half-duplex.
For more information on configuring this device, see ifconfig(8). The em
driver supports polling(4).
HARDWARE
The em driver supports Gigabit Ethernet adapters based on the Intel
82540, 82541ER, 82541PI, 82542, 82543, 82544, 82545, 82546, 82546EB,
82546GB, 82547, 82571, 82572, 82573, and 82574 controller chips:
· Intel PRO/1000 CT Network Connection (82547)
· Intel PRO/1000 F Server Adapter (82543)
· Intel PRO/1000 Gigabit Server Adapter (82542)
· Intel PRO/1000 GT Desktop Adapter (82541PI)
· Intel PRO/1000 MF Dual Port Server Adapter (82546)
· Intel PRO/1000 MF Server Adapter (82545)
· Intel PRO/1000 MF Server Adapter (LX) (82545)
· Intel PRO/1000 MT Desktop Adapter (82540)
· Intel PRO/1000 MT Desktop Adapter (82541)
· Intel PRO/1000 MT Dual Port Server Adapter (82546)
· Intel PRO/1000 MT Quad Port Server Adapter (82546EB)
· Intel PRO/1000 MT Server Adapter (82545)
· Intel PRO/1000 PF Dual Port Server Adapter (82571)
· Intel PRO/1000 PF Quad Port Server Adapter (82571)
· Intel PRO/1000 PF Server Adapter (82572)
· Intel PRO/1000 PT Desktop Adapter (82572)
· Intel PRO/1000 PT Dual Port Server Adapter (82571)
· Intel PRO/1000 PT Quad Port Server Adapter (82571)
· Intel PRO/1000 PT Server Adapter (82572)
· Intel PRO/1000 T Desktop Adapter (82544)
· Intel PRO/1000 T Server Adapter (82543)
· Intel PRO/1000 XF Server Adapter (82544)
· Intel PRO/1000 XT Server Adapter (82544)
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or
stored in loader.conf(5).
hw.em.int_throttle_ceil
Hardware interrupt throttling rate. The default value is
10000Hz.
hw.em.rxd
Number of receive descriptors allocated by the driver. The
default value is 256. The 82542 and 82543-based adapters can
handle up to 256 descriptors, while others can have up to 4096.
hw.em.txd
Number of transmit descriptors allocated by the driver. The
default value is 256. The 82542 and 82543-based adapters can
handle up to 256 descriptors, while others can have up to 4096.
hw.em.int_tx_nsegs
This value controls how many transmit descriptors should be con‐
sumed by the hardware before the hardware generates a transmit
interrupt. The default value is 1/16 of the number of transmit
descriptors. If polling(4) is not used on the hardware and the
major part of the transmitted data are bulk data, this value
could safely be set to 1/2 of the number of transmit descriptors.
DIAGNOSTICS
em%d: Unable to allocate bus resource: memory A fatal initialization
error has occurred.
em%d: Unable to allocate bus resource: interrupt A fatal initialization
error has occurred.
em%d: watchdog timeout -- resetting The device has stopped responding to
the network, or there is a problem with the network connection (cable).
SUPPORT
For general information and support, go to the Intel support website at:
http://support.intel.com.
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related
to the issue to ⟨freebsdnic@mailbox.intel.com⟩.
SEE ALSOarp(4), ifmedia(4), netintro(4), ng_ether(4), polling(4), vlan(4),
ifconfig(8)HISTORY
The em device driver first appeared in FreeBSD 4.4.
AUTHORS
The em driver was written by Intel Corporation
⟨freebsdnic@mailbox.intel.com⟩.
BSD February 27, 2009 BSD