PCTR(4) OpenBSD Programmer's Manual (i386) PCTR(4)NAMEpctr - driver for CPU performance counters
SYNOPSIS
pseudo-device pctr 1
DESCRIPTION
The pctr device provides access to the performance counters on AMD and
Intel brand processors, and to the TSC on others.
Intel processors have two 40-bit performance counters which can be
programmed to count events such as cache misses, branch target buffer
hits, TLB misses, dual-issues, interrupts, pipeline flushes, and more.
While AMD processors have four 48-bit counters, their precision is
decreased to 40 bits.
There is one ioctl call to read the status of all counters, and one ioctl
call to program the function of each counter. All require the following
includes:
#include <sys/types.h>
#include <machine/cpu.h>
#include <machine/pctr.h>
The current state of all counters can be read with the PCIOCRD ioctl,
which takes an argument of type struct pctrst:
#define PCTR_NUM 4
struct pctrst {
u_int pctr_fn[PCTR_NUM];
pctrval pctr_tsc;
pctrval pctr_hwc[PCTR_NUM];
};
In this structure, ctr_fn contains the functions of the counters, as
previously set by the PCIOCS0, PCIOCS1, PCIOCS2 and PCIOCS3 ioctls (see
below). pctr_hwc contains the actual value of the hardware counters.
pctr_tsc is a free-running, 64-bit cycle counter.
The functions of the counters can be programmed with ioctls PCIOCS0,
PCIOCS1, PCIOCS2 and PCIOCS3 which require a writeable file descriptor
and take an argument of type unsigned int. The meaning of this integer
is dependent on the particular CPU.
Time stamp counter
The time stamp counter is available on most of the AMD K6, Intel Pentium
and higher class CPUs, as well as on some 486s and non-intel CPUs. It is
set to zero at boot time, and then increments with each cycle. Because
the counter is 64-bits wide, it does not overflow.
The time stamp counter can be read directly from user-mode using the
rdtsc() macro, which returns a 64-bit value of type pctrval. The
following example illustrates a simple use of rdtsc() to measure the
execution time of a hypothetical subroutine called functionx():
void
time_functionx(void)
{
pctrval tsc;
tsc = rdtsc();
functionx();
tsc = rdtsc() - tsc;
printf("Functionx took %llu cycles.\n", tsc);
}
The value of the time stamp counter is also returned by the PCIOCRD
ioctl, so that one can get an exact timestamp on readings of the hardware
event counters.
Intel Pentium counters
The Intel Pentium counters are programmed with a 9 bit function. The top
three bits contain the following flags:
P5CTR_K Enables counting of events that occur in kernel mode.
P5CTR_U Enables counting of events that occur in user mode. You must
set at least one of P5CTR_U and P5CTR_K to count anything.
P5CTR_C When this flag is set, the counter attempts to count the number
of cycles spent servicing a particular event, rather than simply
the number of occurrences of that event.
The bottom 6 bits set the particular event counted. A list of possible
event functions could be obtained by running a pctr(1) command with -l
option.
Counters for AMD K6, Intel Pentium Pro and newer CPUs
Unlike the Pentium counters, these counters can be read directly from
user-mode without need to invoke the kernel. The macro rdpmc(ctr) takes
0, 1, 2 or 3 as an argument to specify a counter, and returns that
counter's 40-bit value (which will be of type pctrval). This is
generally preferable to making a system call as it introduces less
distortion in measurements.
Counter functions supported by these CPUs contain several parts. The
most significant byte (an 8-bit integer shifted left by PCTR_CM_SHIFT)
contains a counter mask. If non-zero, this sets a threshold for the
number of times an event must occur in one cycle for the counter to be
incremented. The counter mask can therefore be used to count cycles in
which an event occurs at least some number of times. The next byte
contains several flags:
PCTR_U Enables counting of events that occur in user mode.
PCTR_K Enables counting of events that occur in kernel mode. You must
set at least one of PCTR_K and PCTR_U to count anything.
PCTR_E Counts edges rather than cycles. For some functions this allows
you to get an estimate of the number of events rather than the
number of cycles occupied by those events.
PCTR_EN Enable counters. This bit must be set in the function for
counter 0 in order for either of the counters to be enabled.
This bit should probably be set in counter 1 as well.
PCTR_I Inverts the sense of the counter mask. When this bit is set,
the counter only increments on cycles in which there are no more
events than specified in the counter mask.
The next byte (shifted left by the PCTR_UM_SHIFT) contains flags specific
to the event being counted, also known as the unit mask.
For events dealing with the L2 cache, the following flags are valid on
Intel brand processors:
PCTR_UM_M Count events involving modified cache coherency state lines.
PCTR_UM_E Count events involving exclusive cache coherency state lines.
PCTR_UM_S Count events involving shared cache coherency state lines.
PCTR_UM_I Count events involving invalid cache coherency state lines.
To measure all L2 cache activity, all these bits should be set. They can
be set with the macro PCTR_UM_MESI which contains the bitwise or of all
of the above.
For event types dealing with bus transactions, there is another flag that
can be set in the unit mask:
PCTR_UM_A Count all appropriate bus events, not just those initiated by
the processor.
Events marked (MESI) require the PCTR_UM_[MESI] bits in the unit mask.
Events marked (A) can take the PCTR_UM_A bit.
Finally, the least significant byte of the counter function is the event
type to count. A list of possible event functions could be obtained by
running a pctr(1) command with -l option.
FILES
/dev/pctr
ERRORS
[ENODEV] An attempt was made to set the counter functions on a CPU that
does not support counters.
[EINVAL] An invalid counter function was provided as an argument to the
PCIOCSx ioctl.
[EPERM] An attempt was made to set the counter functions, but the
device was not open for writing.
SEE ALSOpctr(1), ioctl(2)HISTORY
A pctr device first appeared in OpenBSD 2.0 but was subsequently extended
to support AMD and newer Intel CPUs in OpenBSD 4.3.
AUTHORS
The pctr device was written by David Mazieres <dm@lcs.mit.edu>.
BUGS
Not all counter functions are completely accurate. Some of the functions
may not make any sense at all. Also you should be aware of the
possibility of an interrupt between invocations of rdpmc() and/or rdtsc()
that can potentially decrease the accuracy of measurements.
OpenBSD 4.9 February 11, 2008 OpenBSD 4.9