GRD2CPT(1) Generic Mapping Tools GRD2CPT(1)NAMEgrd2cpt - Make a color palette table from grid files
SYNOPSISgrd2cpt grdfiles [ -Ccptmaster ] [ -D ] [ -Enlevels ] [ -I ] [ -Lmin‐
limit/maxlimit ] [ -M ] [ -N ] [ -Q[i|o] ] [ -Rwest/east/south/north[r]
] [ -Szstart/zstop/zinc ] [ -T-|+|_|= ] [ -V ] [ -Z ]
DESCRIPTIONgrd2cpt reads one or more grid files and writes a color palette (cpt)
file to standard output. The cpt file is based on an existing master
cpt file of your choice, and the mapping from data value to colors is
through the data's cumulative distribution function (CDF), so that the
colors are histogram equalized. Thus if the grid(s) and the resulting
cpt file are used in grdimage with a linear projection, the colors will
be uniformly distributed in area on the plot. Let z be the data values
in the grid. Define CDF(Z) = (# of z < Z) / (# of z in grid). (NaNs
are ignored). These z-values are then normalized to the master cpt
file and colors are sampled at the desired intervals.
The color palette includes three additional colors beyond the range of
z-values. These are the background color (B) assigned to values lower
than the lowest z-value, the foreground color (F) assigned to values
higher than the highest z-value, and the NaN color (N) painted
whereever values are undefined.
If the master cpt file includes B, F, and N entries, these will be
copied into the new master file. If not, the parameters COLOR_BACK‐
GROUND, COLOR_FOREGROUND, and COLOR_NAN from the .gmtdefaults4 file or
the command line will be used. This default behavior can be overruled
using the options -D, -M or -N.
The color model (RGB, HSV or CMYK) of the palette created by makecpt
will be the same as specified in the header of the master cpt file.
When there is no COLOR_MODEL entry in the master cpt file, the
COLOR_MODEL specified in the .gmtdefaults4 file or on the command line
will be used.
grdfiles
Names of one or more 2-D binary grid files used to derive the
color palette table. All grids need to have the same size and
dimensions. (See GRID FILE FORMATS below).
OPTIONS-C Selects the master color table to use in the interpolation.
Choose among the built-in tables (type grd2cpt to see the list)
or give the name of an existing cpt file [Default gives a rain‐
bow cpt file].
-D Select the colors for lowest and highest z-values in the output
cpt file as the back- and foreground colors that will be written
to the cpt file [Default uses the colors specified in the master
file, or those defined by the parameters COLOR_BACKGROUND,
COLOR_FOREGROUND, and COLOR_NAN].
-E Create a linear color table by dividing the grid z-range into
nlevels equidistant slices.
-I Reverses the sense of color progression in the master cpt file.
Also exchanges the foreground and background colors, including
those specified by the parameters COLOR_BACKGROUND and
COLOR_FOREGROUND.
-L Limit range of cpt file to minlimit/maxlimit, and don't count
data outside range when estimating CDF(Z). [Default uses min
and max of data.]
-M Overrule background, foreground, and NaN colors specified in the
master cpt file with the values of the parameters COLOR_BACK‐
GROUND, COLOR_FOREGROUND, and COLOR_NAN specified in the .gmtde‐
faults4 file or on the command line. When combined with -D,
only COLOR_NAN is considered.
-N Do not write out the background, foreground, and NaN-color
fields [Default will write them].
-Q Selects a logarithmic interpolation scheme [Default is linear].
-Qi expects input z-values to be log10(z), assigns colors, and
writes out z [Default]. -Qo takes log10(z) first, assigns col‐
ors, and writes out z.
-R xmin, xmax, ymin, and ymax specify the Region of interest. For
geographic regions, these limits correspond to west, east,
south, and north and you may specify them in decimal degrees or
in [+-]dd:mm[:ss.xxx][W|E|S|N] format. Append r if lower left
and upper right map coordinates are given instead of w/e/s/n.
The two shorthands -Rg and -Rd stand for global domain (0/360
and -180/+180 in longitude respectively, with -90/+90 in lati‐
tude). Alternatively, specify the name of an existing grid file
and the -R settings (and grid spacing, if applicable) are copied
from the grid. For calendar time coordinates you may either
give (a) relative time (relative to the selected TIME_EPOCH and
in the selected TIME_UNIT; append t to -JX|x), or (b) absolute
time of the form [date]T[clock] (append T to -JX|x). At least
one of date and clock must be present; the T is always required.
The date string must be of the form [-]yyyy[-mm[-dd]] (Gregorian
calendar) or yyyy[-Www[-d]] (ISO week calendar), while the clock
string must be of the form hh:mm:ss[.xxx]. The use of delim‐
iters and their type and positions must be exactly as indicated
(however, input, output and plot formats are customizable; see
gmtdefaults).
-S Set steps in cpt file. Calculate entries in cpt file from
zstart to zstop in steps of (zinc). [Default chooses arbitrary
values by a crazy scheme.]
-T Force the color table to be symmetric about zero (from -R to
+R). Append flag to set the range R: - for R =|zmin|, + for R =
|zmax|, _ for R = min(|zmin|, |zmax|), or = for R = max(|zmin|,
|zmax|).
-V Verbose operation. This will write CDF(Z) estimates to stderr.
[Default is silent.]
-Z Will create a continuous color palette. [Default is discontinu‐
ous, i.e., constant color intervals]
GRID FILE FORMATS
GMT is able to recognize many of the commonly used grid file formats,
as well as the precision, scale and offset of the values contained in
the grid file. When GMT needs a little help with that, you can add the
suffix =id[/scale/offset[/nan]], where id is a two-letter identifier of
the grid type and precision, and scale and offset are optional scale
factor and offset to be applied to all grid values, and nan is the
value used to indicate missing data. See grdreformat(1) and Section
4.17 of the GMT Technical Reference and Cookbook for more information.
When reading a netCDF file that contains multiple grids, GMT will read,
by default, the first 2-dimensional grid that can find in that file. To
coax GMT into reading another multi-dimensional variable in the grid
file, append ?varname to the file name, where varname is the name of
the variable. Note that you may need to escape the special meaning of ?
in your shell program by putting a backslash in front of it, or by
placing the filename and suffix between quotes or double quotes. See
grdreformat(1) and Section 4.18 of the GMT Technical Reference and
Cookbook for more information, particularly on how to read splices of
3-, 4-, or 5-dimensional grids.
EXAMPLES
Sometimes you don't want to make a cpt file (yet) but would find it
helpful to know that 90% of your data lie between z1 and z2, something
you cannot learn from grdinfo. So you can do this to see some points
on the CDF(Z) curve (use -V option to see more):
grd2cpt mydata.grd -V > /dev/null
To make a cpt file with entries from 0 to 200 in steps of 20, and
ignore data below zero in computing CDF(Z), and use the built-in master
cpt file relief, run
grd2cpt mydata.grd -Crelief -L0/10000 -S0/200/20 > mydata.cpt
SEE ALSOgmtdefaults(1), GMT(1), grdhisteq(1), grdinfo(1), makecpt(1)GMT 4.5.14 1 Nov 2015 GRD2CPT(1)
