MIDI(4) OpenBSD Programmer's Manual MIDI(4)NAMEmidi - raw device independent interface to MIDI ports
SYNOPSIS
midi* at autri?
midi* at eap?
midi* at envy?
midi* at mpu?
midi* at sb?
midi* at umidi?
midi* at ym?
DESCRIPTION
The midi driver makes MIDI ports available to user applications. A midi
device corresponds to 2 MIDI ports: one input port and one output port.
Data received on the input port is not interpreted and is passed to the
user program as-is. Similarly, data issued by the user program is sent
as-is to the output port.
Only one process may hold open a midi device at a given time, although
file descriptors may be shared between processes once the first open
completes. If it is opened read-only (write-only) only the input
(output) MIDI port is available.
Writing to the device
A process can send raw MIDI data to the output port by using the write(2)
system call. Data is queued and the system call returns immediately; the
data is sent as fast as possible to the output MIDI port. However, if
the in-kernel buffer is full or the requested amount is too large, then
write(2) may block. The current size of the in-kernel buffer is 1024
bytes, which ensures that write(2) isn't blocking in most situations.
Reading from the device
Data received from the input MIDI port is stored into the in-kernel
buffer. A process can retrieve its contents by using the read(2) system
call. If there is less data than the amount requested for reading, then
a shorter amount is returned. If no data is available, then the read(2)
system call will block until data is received, and then return
immediately.
The MIDI protocol has been designed for real-time performance and doesn't
support flow control. An application must be able to read the incoming
data fast enough (the MIDI standard's maximum rate is 3125 bytes per
second). The kernel can buffer up to 1024 bytes; once the buffer is full
input will be silently discarded.
Polling the device
A process can use the poll(2) system call to poll for the following
events:
POLLIN The in-kernel input buffer isn't empty, i.e. at least one byte
is available for reading. A subsequent call to read(2) will not
be blocking.
POLLOUT The in-kernel output buffer is empty, thus a subsequent call to
write(2) will not be blocking if a reasonable amount of data is
written (currently less that 1024 bytes).
Using the poll(2) system call is the recommended way to handle multiple
midi devices in a real-time MIDI application.
Non-blocking I/O
If the midi device is opened with the O_NONBLOCK flag (see open(2)), then
subsequent calls to read(2) or write(2) will never block. The write(2)
system call may write less bytes than requested, or may return EAGAIN if
no data could be sent or queued. Similarly, the read(2) system call may
return EAGAIN if no input is available.
Note that even if non-blocking I/O is not selected, read(2) and write(2)
system calls are non-blocking when the kernel buffers permit it.
FILES
/dev/rmidi* midi devices
EXAMPLES
The following command could record the memory dump of a synthesizer in a
file:
$ cat -u /dev/rmidi2 >dumpfile
A MIDI keyboard could be connected to a synthesizer by the command:
$ cat -u /dev/rmidi1 >/dev/rmidi2
The input port could be connected to the output port by the command:
$ cat -u <>/dev/rmidi1 >&0
The following example reads MIDI timing events from an input device, MIDI
common and voice events from another input device, and sends the result
to a third (output) device.
#define BUFSIZE 0x100
#define ISTIMING(c) ((c) == 0xf8 || (c) == 0xfa || (c) == 0xfc)
#define ISCOMMON(c) ((c) < 0xf8)
int ofd;
struct pollfd ifd[2];
unsigned char ibuf[BUFSIZE], obuf[2 * BUFSIZE];
ssize_t iused, oused, i;
ifd[0].events = ifd[1].events = POLLIN;
for (;;) {
oused = 0;
if (poll(ifd, 2, -1) == -1)
errx(1, "poll");
if (ifd[0].revents & POLLIN) {
if ((iused = read(ifd[0].fd, ibuf, BUFSIZE)) == -1)
errx(1, "read");
for (i = 0; i < iused; i++)
if (ISTIMING(ibuf[i]))
obuf[oused++] = ibuf[i];
}
if (ifd[1].revents & POLLIN) {
if ((iused = read(ifd[1].fd, ibuf, BUFSIZE)) == -1)
errx(1, "read");
for (i = 0; i < iused; i++)
if (ISCOMMON(ibuf[i]))
obuf[oused++] = ibuf[i];
}
if (write(ofd, obuf, oused) == -1)
errx(1, "write");
}
In the above example, unless kernel buffers are full, processing is done
in real-time without any noticeable latency; as expected, the only
blocking system call is poll(2).
ERRORS
If open(2), read(2), write(2), or poll(2) fail then errno(2) may be set
to one of:
[ENXIO] The device is opened read-only (write-only) but write(2)
(read(2)) was called.
[EIO] The device is being detached while a process has been
trying to read or write (for instance an umidi(4) device
has been unplugged).
[EAGAIN] Non-blocking I/O was selected and the output buffer is full
(on writing) or the input buffer is empty (on reading).
[EBUSY] The device is already open by another process.
SEE ALSOautri(4), eap(4), envy(4), mpu(4), sb(4), sequencer(4), umidi(4), ym(4)HISTORY
The midi driver first appeared in OpenBSD 2.5.
AUTHORS
The midi driver was originally written by Lennart Augustsson and later
largely rewritten by Alexandre Ratchov.
CAVEATS
MIDI hardware was designed for real time performance and software using
such hardware must be able to process MIDI events without any noticeable
latency (typically no more than 5ms, which corresponds to the time it
takes to the sound to propagate 1.75 meters).
The OpenBSD midi driver processes data fast enough, however if a MIDI
application tries to write data faster than the hardware is able to
process it (typically 3125 bytes per second), then kernel buffers may
become full and the application may be blocked.
The other common reason for MIDI data being delayed is the system load.
Processes cannot be preempted while running in kernel mode. If there are
too much processes running concurrently (especially if they are running a
lot of expensive system calls) then the scheduling of a real-time MIDI
application may be delayed. Even on low-end machines this delay hardly
reaches a few milliseconds provided that the system load is reasonable.
A real-time MIDI application can avoid being swapped by locking its
memory (see mlock(2) and mlockall(2)).
BUGS
For a given device, even if the physical MIDI input and output ports are
independent, there is no way for one process to use the input MIDI port
and for another process to use the output MIDI port at the same time.
OpenBSD 4.9 October 4, 2010 OpenBSD 4.9