STRUCT USB_DEVICE(9) Host-Side Data Types and Macro STRUCT USB_DEVICE(9)NAMEstruct_usb_device - kernel's representation of a USB device
SYNOPSIS
struct usb_device {
int devnum;
char devpath[16];
u32 route;
enum usb_device_state state;
enum usb_device_speed speed;
struct usb_tt * tt;
int ttport;
unsigned int toggle[2];
struct usb_device * parent;
struct usb_bus * bus;
struct usb_host_endpoint ep0;
struct device dev;
struct usb_device_descriptor descriptor;
struct usb_host_bos * bos;
struct usb_host_config * config;
struct usb_host_config * actconfig;
struct usb_host_endpoint * ep_in[16];
struct usb_host_endpoint * ep_out[16];
char ** rawdescriptors;
unsigned short bus_mA;
u8 portnum;
u8 level;
unsigned can_submit:1;
unsigned persist_enabled:1;
unsigned have_langid:1;
unsigned authorized:1;
unsigned authenticated:1;
unsigned wusb:1;
unsigned lpm_capable:1;
unsigned usb2_hw_lpm_capable:1;
unsigned usb2_hw_lpm_besl_capable:1;
unsigned usb2_hw_lpm_enabled:1;
unsigned usb3_lpm_enabled:1;
int string_langid;
char * product;
char * manufacturer;
char * serial;
struct list_head filelist;
int maxchild;
u32 quirks;
atomic_t urbnum;
unsigned long active_duration;
#ifdef CONFIG_PM
unsigned long connect_time;
unsigned do_remote_wakeup:1;
unsigned reset_resume:1;
unsigned port_is_suspended:1;
#endif
struct wusb_dev * wusb_dev;
int slot_id;
enum usb_device_removable removable;
struct usb2_lpm_parameters l1_params;
struct usb3_lpm_parameters u1_params;
struct usb3_lpm_parameters u2_params;
unsigned lpm_disable_count;
};
MEMBERS
devnum
device number; address on a USB bus
devpath[16]
device ID string for use in messages (e.g., /port/...)
route
tree topology hex string for use with xHCI
state
device state: configured, not attached, etc.
speed
device speed: high/full/low (or error)
tt
Transaction Translator info; used with low/full speed dev,
highspeed hub
ttport
device port on that tt hub
toggle[2]
one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints
parent
our hub, unless we're the root
bus
bus we're part of
ep0
endpoint 0 data (default control pipe)
dev
generic device interface
descriptor
USB device descriptor
bos
USB device BOS descriptor set
config
all of the device's configs
actconfig
the active configuration
ep_in[16]
array of IN endpoints
ep_out[16]
array of OUT endpoints
rawdescriptors
raw descriptors for each config
bus_mA
Current available from the bus
portnum
parent port number (origin 1)
level
number of USB hub ancestors
can_submit
URBs may be submitted
persist_enabled
USB_PERSIST enabled for this device
have_langid
whether string_langid is valid
authorized
policy has said we can use it; (user space) policy determines if we
authorize this device to be used or not. By default, wired USB
devices are authorized. WUSB devices are not, until we authorize
them from user space. FIXME -- complete doc
authenticated
Crypto authentication passed
wusb
device is Wireless USB
lpm_capable
device supports LPM
usb2_hw_lpm_capable
device can perform USB2 hardware LPM
usb2_hw_lpm_besl_capable
device can perform USB2 hardware BESL LPM
usb2_hw_lpm_enabled
USB2 hardware LPM enabled
usb3_lpm_enabled
USB3 hardware LPM enabled
string_langid
language ID for strings
product
iProduct string, if present (static)
manufacturer
iManufacturer string, if present (static)
serial
iSerialNumber string, if present (static)
filelist
usbfs files that are open to this device
maxchild
number of ports if hub
quirks
quirks of the whole device
urbnum
number of URBs submitted for the whole device
active_duration
total time device is not suspended
connect_time
time device was first connected
do_remote_wakeup
remote wakeup should be enabled
reset_resume
needs reset instead of resume
port_is_suspended
the upstream port is suspended (L2 or U3)
wusb_dev
if this is a Wireless USB device, link to the WUSB specific data
for the device.
slot_id
Slot ID assigned by xHCI
removable
Device can be physically removed from this port
l1_params
best effor service latency for USB2 L1 LPM state, and L1 timeout.
u1_params
exit latencies for USB3 U1 LPM state, and hub-initiated timeout.
u2_params
exit latencies for USB3 U2 LPM state, and hub-initiated timeout.
lpm_disable_count
Ref count used by usb_disable_lpm and usb_enable_lpm to keep track
of the number of functions that require USB 3.0 Link Power
Management to be disabled for this usb_device. This count should
only be manipulated by those functions, with the bandwidth_mutex is
held.
NOTES
Usbcore drivers should not set usbdev->state directly. Instead use
usb_set_device_state.
COPYRIGHTKernel Hackers Manual 3.11 November 2013 STRUCT USB_DEVICE(9)
