ZMQ_PGM(7) 0MQ Manual ZMQ_PGM(7)NAME
zmq_pgm - 0MQ reliable multicast transport using PGM
SYNOPSIS
PGM (Pragmatic General Multicast) is a protocol for reliable multicast
transport of data over IP networks.
DESCRIPTION
0MQ implements two variants of PGM, the standard protocol where PGM
datagrams are layered directly on top of IP datagrams as defined by RFC
3208 (the pgm transport) and "Encapsulated PGM" or EPGM where PGM
datagrams are encapsulated inside UDP datagrams (the epgm transport).
The pgm and epgm transports can only be used with the ZMQ_PUB and
ZMQ_SUB socket types.
Further, PGM sockets are rate limited by default. For details, refer to
the ZMQ_RATE, and ZMQ_RECOVERY_IVL options documented in
zmq_setsockopt(3).
Caution
The pgm transport implementation requires access to raw IP sockets.
Additional privileges may be required on some operating systems for
this operation. Applications not requiring direct interoperability
with other PGM implementations are encouraged to use the epgm
transport instead which does not require any special privileges.
ADDRESSING
A 0MQ endpoint is a string consisting of a transport:// followed by an
address. The transport specifies the underlying protocol to use. The
address specifies the transport-specific address to connect to.
For the PGM transport, the transport is pgm, and for the EPGM protocol
the transport is epgm. The meaning of the address part is defined
below.
Connecting a socket
When connecting a socket to a peer address using zmq_connect() with the
pgm or epgm transport, the endpoint shall be interpreted as an
interface followed by a semicolon, followed by a multicast address,
followed by a colon and a port number.
An interface may be specified by either of the following:
· The interface name as defined by the operating system.
· The primary IPv4 address assigned to the interface, in its numeric
representation.
Note
Interface names are not standardised in any way and should be
assumed to be arbitrary and platform dependent. On Win32 platforms
no short interface names exist, thus only the primary IPv4 address
may be used to specify an interface. The interface part can be
omitted, in that case the default one will be selected.
A multicast address is specified by an IPv4 multicast address in its
numeric representation.
WIRE FORMAT
Consecutive PGM datagrams are interpreted by 0MQ as a single continuous
stream of data where 0MQ messages are not necessarily aligned with PGM
datagram boundaries and a single 0MQ message may span several PGM
datagrams. This stream of data consists of 0MQ messages encapsulated in
frames as described in zmq_tcp(7).
PGM datagram payload
The following ABNF grammar represents the payload of a single PGM
datagram as used by 0MQ:
datagram = (offset data)
offset = 2OCTET
data = *OCTET
In order for late joining consumers to be able to identify message
boundaries, each PGM datagram payload starts with a 16-bit unsigned
integer in network byte order specifying either the offset of the first
message frame in the datagram or containing the value 0xFFFF if the
datagram contains solely an intermediate part of a larger message.
Note that offset specifies where the first message begins rather than
the first message part. Thus, if there are trailing message parts at
the beginning of the packet the offset ignores them and points to first
initial message part in the packet.
The following diagram illustrates the layout of a single PGM datagram
payload:
+------------------+----------------------+
| offset (16 bits) | data |
+------------------+----------------------+
The following diagram further illustrates how three example 0MQ frames
are laid out in consecutive PGM datagram payloads:
First datagram payload
+--------------+-------------+---------------------+
| Frame offset | Frame 1 | Frame 2, part 1 |
| 0x0000 | (Message 1) | (Message 2, part 1) |
+--------------+-------------+---------------------+
Second datagram payload
+--------------+---------------------+
| Frame offset | Frame 2, part 2 |
| 0xFFFF | (Message 2, part 2) |
+--------------+---------------------+
Third datagram payload
+--------------+----------------------------+-------------+
| Frame offset | Frame 2, final 8 bytes | Frame 3 |
| 0x0008 | (Message 2, final 8 bytes) | (Message 3) |
+--------------+----------------------------+-------------+
EXAMPLE
Connecting a socket.
// Connecting to the multicast address 239.192.1.1, port 5555,
// using the first Ethernet network interface on Linux
// and the Encapsulated PGM protocol
rc = zmq_connect(socket, "epgm://eth0;239.192.1.1:5555");
assert (rc == 0);
// Connecting to the multicast address 239.192.1.1, port 5555,
// using the network interface with the address 192.168.1.1
// and the standard PGM protocol
rc = zmq_connect(socket, "pgm://192.168.1.1;239.192.1.1:5555");
assert (rc == 0);
SEE ALSOzmq_connect(3)zmq_setsockopt(3)zmq_tcp(7)zmq_ipc(7)zmq_inproc(7)zmq(7)AUTHORS
This page was written by the 0MQ community. To make a change please
read the 0MQ Contribution Policy at
http://www.zeromq.org/docs:contributing.
0MQ 4.0.1 03/10/2014 ZMQ_PGM(7)
