System(DSP)

Description

A System file is one of the Installable Driver/Tunable Parameters kernel configuration files that contains information needed to incorporate a particular kernel module into the next system configuration. General configuration information about the module type is described in the Master file. When the System component of a module's Driver Software Package (DSP) is installed, idinstall(ADM) stores the module's System file information in /etc/conf/sdevice.d/module-name, where the file module-name is the name of the module being installed. Never access /etc/conf/sdevice.d/module-name directly; use idinstall(ADM).

Blank lines in System files and lines beginning with # or * are considered comments and are ignored.

The first non-comment line should be:

   $version 2

Older System file versions are supported by idinstall (see Compatibility Considerations).

Optionally, following the $version line, the following line can appear:

   	$static

The presence of the $static line in the file indicates that the module should be statically configured (directly linked into the kernel image) even if it is capable of being loadable.

Following these lines are one or more lines in the following format:

module-name configure unit ipl itype ivec sioa eioa scma ecma dmachan [cpu]

These lines contain configuration information for each instance of the module. For example, if two instances of a device are to be configured, two lines of System file definitions are required for the device.

Each of these configuration lines contains 11 or 12 fields, with the twelfth field (cpu) being optional. Each field must be delimited by white space and specify a value. Note that, except for the first two fields (module-name and configure), the remaining fields on this line are used for hardware-related modules only. That is, these fields apply only to modules that have the h ``characteristics'' flag set in the associated Master file. When a field does not apply to the module--regardless of the module type--the unused field must contain the value 0 (except for dmachan, which if unused must contain the value -1).

module-name

Identifies the internal name of the module. The field value must match the module name specified in the module's Master file.

configure

Indicates (Y or N) whether idbuild(ADM) should configure this instance of the module into the system. Note that this field can be used to configure statically linked modules or to configure dynamically loadable modules.

unit

Specifies the number of subdevices attached to a controller or pseudo device, or this field can be used to encode an arbitrary, module-dependent numeric value. When this field is not used, it should contain the value 0.

The DSP for an HBA driver should set unit to -1 so that the SDI subsystem can assign a unique unit value to this instance of the driver. SDI assigns a value that represents the controller number (the ``c0'' part of c0b0t0d0s0) to the unit field when the HBA driver is initialized. SDI interprets -1 as meaning that the HBA instance has not yet been assigned a unit value. Modifying this value after driver installation or setting it to a value other than -1 in the DSP corrupts the SDI subsystem.

ipl

Specifies the interrupt priority level for the device controlled by this module and the priority at which the module's interrupt handler will run. Valid values are:

0

Used if the module is not a hardware module or does not have an interrupt handler.

1

(lowest priority); used for software interrupts and should not be used for hardware drivers

5

Used for SDI HBA devices.

6

Used for network adapter cards and other STREAMS devices.

8

Reserved for the clock tick interrupt.

9

Reserved for serial ports (asyc).

itype

Indicates the type of interrupt sharing (if any) this hardware module supports. Note that, if a module supports a number of interrupt sources, it requires multiple lines in the System file, and each line may specify a different itype field value.

Valid values are:

0

This instance of the device does not use interrupts.

1

This instance of the device uses an edge-triggered interrupt vector that cannot be shared, not even with another instance of the same module.

2

This instance of the device uses an edge-triggered interrupt vector that can be shared with another instance of the same module, but can not be shared with other modules.

3

This instance of the device uses an edge-triggered interrupt vector that can be shared with any instance of any hardware modules.

4

This instance of the device uses a level-sensitive interrupt vector that can be shared with any instance of any hardware module. PCI devices must have this value and be able to share interrupts.

Each interrupt is programmed individually according to the settings for each device. The driver specifies the default settings, but these may be overridden by BIOS information or user overrides.

When this field is not used, it must contain the value 0.

vector

Specifies the interrupt vector number used by this instance of the device. Valid values are a decimal number from 1 through the value of the highest interrupt vector number supported by the system.

Note that more than one device can share an interrupt vector number if the devices use the same itype interrupt, and that interrupt is of a type that can be shared. Note also that every instance of every module that shares an interrupt vector number must specify the same ipl values.

When this field is not used, it should contain the value 0.

sioa

Start I/O address. Specifies the lowest I/O port address through which the device communicates. Valid values are a hexadecimal number from 0 through FFFF. For non-hardware modules or devices without I/O ports, this field should contain the value 0.

eioa

End I/O address. Specifies the highest (inclusive) I/O port address through which the device communicates. Valid values are a hexadecimal number from 1 through FFFF. Note that the value of the eioa field must be greater than or equal to the value of the sioa field. For non-hardware modules or devices without I/O ports, this field should contain the value 0.

scma

Start memory controller address. Specifies the lowest address in memory through which the device communicates. Valid values are a hexadecimal number from 10000 through FFFFFFFF. For non-hardware drivers or devices without controller memory, this field should contain the value 0.

ecma

End memory controller address. Specifies the highest (inclusive) address in memory through which the device communicates. Valid values are a hexadecimal number from 10000 through FFFFFFFF. Note that the value of the ecma field must be greater than or equal to the value of the scma field. For non-hardware modules or devices without controller memory, this field should contain the value 0.

dmachan

For hardware modules that use DMA channels, specifies the DMA channel number. Valid values are a decimal number from 0 through 7. For non-hardware modules or devices that do not use channelized DMA, this field should contain the value -1.

cpu

Optional field. Specifies on a multiprocessor system a CPU number to which the module should be bound (driver code will run only on the specified CPU). This binding only applies to interrupt handlers and DDI entry points as described in Section D2 manual pages in Section D2 manual pages. Currently, the same CPU number must be given on all System lines for a module.

Warnings

References

Backward compatibility

Compatibility considerations

Because some fields moved between the Master file and the System file, version 0 and version 1 Master and System files must be installed together, using a single invocation of the idinstall command. This allows idinstall to move the fields between the files during conversion.

Version 0 System files are not supported for exec modules.

The older formats had fewer fields. In version 1, the ``cpu'' field was in the Master file instead of the System file. In version 0, the ``dmachan'' field was in the Master file instead of the System file and there was no ``cpu'' field.

The older formats had no $static line; Version 1 had a similar but inverted $loadable module-name.