sg_wr_mode man page on Alpinelinux
[printable version]
SG_WR_MODE(8) SG3_UTILS SG_WR_MODE(8)
NAME
sg_wr_mode - write (modify) SCSI mode page
SYNOPSIS
sg_wr_mode [--contents=H,H...] [--dbd] [--force] [--help] [--len=10|6]
[--mask=M,M...] [--page=PG[,SPG]] [--save] [--verbose] [--version]
DEVICE
DESCRIPTION
Writes a modified mode page to DEVICE. Uses the SCSI MODE SENSE (6 or
10 byte variant) command to fetch the existing mode data which includes
a mode page (or subpage). It then combines that with the contents,
potentially masked, and writes the modified mode page with the SCSI
MODE SELECT (6 or 10 byte variant) command. This utility does not mod‐
ify the block descriptor(s); if any block descriptors are fetched by
the MODE SENSE command then the same block descriptors are written back
with the following MODE SELECT command.
If a contents argument is not given then the various components (i.e.
header, block descriptor(s) and mode page) of the "current" values of
the existing mode page are printed out. In this case the mode page is
not altered on the device.
If the contents are specified, and a mask is not specified, then the
contents must match the existing mode page in various aspects unless
the --force option is given. These include length, mode page code and
subpage code if applicable. If all is well then the contents string is
written to DEVICE as the new mode page.
If both contents and mask strings are specified then only bit positions
in the contents corresponding to set bits in the mask are taken while
the existing mode page supplies bit positions corresponding to clear
bits. When a mask is given then the mask and/or the contents may be
shorter than the existing mode page. If the mask is shorter than the
contents then the remaining bytes are taken from the contents. If the
contents are shorter than the existing mode page then the remaining
bytes are taken from the existing mod page.
The force option allows the contents string to be written as the new
mode page without any prior checks on the existing mode page. This
should only be required for vendor specific mode pages. The existing
mode data is ignored apart from the block descriptors which can be sup‐
pressed with the --dbd option if need be.
Changing individual fields in a mode page is probably more easily done
with the sdparm utility. Fields can be identified by acronym or by a
numerical descriptor.
OPTIONS
Arguments to long options are mandatory for short options as well.
-c, --contents=H,H...
where H,H... is a string of comma separated hex numbers each of
which should resolve to a byte value (i.e. 0 to ff inclusive). A
(single) space separated string of hex numbers is also allowed
but the list needs to be in quotes. This is the new contents of
the mode page to be written to DEVICE, potentially filtered by
the mask string.
-c, --contents=-
reads contents string from stdin. The hex numbers in the string
may be comma, space, tab or linefeed (newline) separated. If a
line contains "#" then the remaining characters on that line are
ignored. Otherwise each non separator character should resolve
to a byte value (i.e. 0 to ff inclusive). This forms the new
contents of the mode page to be written to DEVICE, potentially
filtered by the mask string.
-d, --dbd
disable block descriptors (DBD flag in cdb). Some device types
include block descriptors in the mode data returned by a MODE
SENSE command. If so the same block descriptors are written by
the MODE SELECT command. This option instructs the MODE SENSE
command not to return any block descriptors. This would be a
sensible default for this utility apart from the fact that not
all SCSI devices support the DBD bit in the cdb.
-f, --force
force the contents string to be taken as the new mode page, or
at least doesn't do checks on the existing mode page. Note that
DEVICE may still reject the new contents for the mode page. Can‐
not be given with the --mask=M,M... option.
-h, --help
output the usage message then exit.
-l, --len=10 | 6
length of the SCSI commands (cdb) sent to DEVICE. The default is
10 so 10 byte MODE SENSE and MODE SELECT commands are issued.
Some old devices don't support the 10 byte variants hence this
option.
-m, --mask=M,M...
where M,M... is a string of comma separated hex numbers each of
which should resolve to a byte value (i.e. 0 to ff inclusive). A
(single) space separated string of hex numbers is also allowed
but the list needs to be in quotes. The mask chooses (bit by
bit) whether the new mode page comes from the contents (mask bit
set) or from the existing mode page (mask bit clear). If the
mask string is shorter than the contents string then the remain‐
ing bytes are taken from the contents string. If the contents
string is shorter than the existing mode page then the remaining
bytes are taken from the existing mode page (i.e. they are left
unaltered).
-p, --page=PG
where PG is the page code value to fetch and modify. The page
code is in hex and should be between 0 and 3e inclusive. Notice
that page code 3f to fetch all mode pages is disallowed.
-p, --page=PG,SPG
where PG is the page code value and SPG is the subpage code
value to fetch and modify. Both values are in hex. The subpage
code should be between 0 and fe inclusive. Notice that subpage
code ff to fetch all mode subpages (for a given mode page or all
mode pages in the case of 3f,ff) is disallowed.
-s, --save
changes the "saved" mode page when MODE SELECT is successful. By
default (i.e. when --save is not used) only the "current" mode
page values are changed when MODE SELECT is successful. In this
case the new mode page will stay in effect until the device is
reset (e.g. power cycled). When it restarts the "saved" values
for the mode page will be re-instated. So to make changes per‐
manent use the --save option.
-v, --verbose
increase the level of verbosity, (i.e. debug output).
-V, --version
print the version string and then exit.
NOTES
This utility does not check whether the contents string is trying to
modify parts of the mode page which are changeable. The device should
do that and if some part is not changeable then it should report:
"Invalid field in parameter list".
Some mode pages are not saveable. If so an attempt to use the --save
option should cause an error to be reported from the device: "Illegal
field in cdb".
The device is required to do various checks before it accepts a new
mode page. If these checks fail then the mode page is not altered and
either a "parameter list length error" or an "invalid field in parame‐
ter list" error is returned by the device in the sense data.
The recommended way to modify a mode page is to read it with a MODE
SENSE, modify some part of it then write it back to the device with a
MODE SELECT command. For example, reading an existing mode page can be
accomplished with 'sg_modes -p=1a -r /dev/sdb > mp_1a.txt' (the power
condition mode page). The mp_1a.txt file can be edited and then used as
the contents string to this utility (e.g. 'sg_wr_mode -p 1a -s -c -
/dev/sdb < mp_1a.txt').
Two fields differ between what is read from the device with MODE SENSE
and what is written to the device with MODE SELECT: the mode data
length is reserved (i.e. zero(es)) in a MODE SELECT command while the
PS bit ((sub)page byte 0 bit 7) in each mode (sub)page is reserved
(zero) in a MODE SELECT command. The PS bit given in the contents
string is zeroed unless the --force option is selected.
EXAMPLES
This utility can be used together with the sg_modes utility. To
re-instate the default mode page values (i.e. the mode page values cho‐
sen by the manufacturer of the device) as both the current and saved
mode page values the following sequence could be used:
$ sg_modes --control=2 --page=1a -r /dev/sda > t
$ sg_wr_mode --page=1a --contents=- --save /dev/sda < t
Next is an example of using a mask to modify the "idle condition
counter" of the "power condition" mode page (0x1a) from 0x28 to 0x37.
Note that the change is not saved so the "idle condition counter" will
revert to 0x28 after the next power cycle. The output from sg_modes is
abridged.
$ sg_modes --page=1a /dev/hdc
>> Power condition (mmc), page_control: current
00 1a 0a 00 03 00 00 00 28 00 00 01 2c
$ sg_wr_mode -p 1a -c 0,0,0,0,0,0,0,37 -m 0,0,0,0,0,0,0,ff /dev/hdc
$ sg_modes -p 1a /dev/hdc
>> Power condition (mmc), page_control: current
00 1a 0a 00 03 00 00 00 37 00 00 01 2c
EXIT STATUS
The exit status of sg_wr_mode is 0 when it is successful. Otherwise see
the sg3_utils(8) man page.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2004-2012 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO war‐
ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR‐
POSE.
SEE ALSO
sdparm(sdparm), sg_modes(sg3_utils), sginfo(sg3_utils)
sg3_utils-1.35 November 2012 SG_WR_MODE(8)
[top]
List of man pages available for Alpinelinux
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
|
Vote for polarhome
|
