SHOREWALL-INTERFACE(5)SHOREWALL-INTERFACE(5)NAME
interfaces - Shorewall interfaces file
SYNOPSIS
/etc/shorewall/interfaces
DESCRIPTION
The interfaces file serves to define the firewall´s network interfaces
to Shorewall. The order of entries in this file is not significant in
determining zone composition.
The columns in the file are as follows.
ZONE - zone-name
Zone for this interface. Must match the name of a zone declared in
/etc/shorewall/zones. You may not list the firewall zone in this
column.
If the interface serves multiple zones that will be defined in the
shorewall-hosts[1](5) file, you should place "-" in this column.
If there are multiple interfaces to the same zone, you must list
them in separate entries.
Example:
#ZONE INTERFACE BROADCAST
loc eth1 -
loc eth2 -
INTERFACE - interface[:port]
Name of interface. Each interface may be listed only once in this
file. You may NOT specify the name of a "virtual" interface (e.g.,
eth0:0) here; see http://www.shorewall.net/FAQ.htm#faq18
You may use wildcards here by specifying a prefix followed by the
plus sign ("+"). For example, if you want to make an entry that
applies to all PPP interfaces, use ´ppp+´; that would match ppp0,
ppp1, ppp2, ...
When using Shorewall versions before 4.1.4, care must be exercised
when using wildcards where there is another zone that uses a
matching specific interface. See shorewall-nesting[2](5) for a
discussion of this problem.
Beginning with Shorewall 4.2.3, Shorewall-perl allows ´+´ as an
interface name.
There is no need to define the loopback interface (lo) in this
file.
(Shorewall-perl only) If a port is given, then the interface must
have been defined previously with the bridge option. The OPTIONS
column may not contain the following options when a port is given.
arp_filter
arp_ignore
bridge
log_martians
mss
optional
proxyarp
routefilter
sourceroute
upnp
BROADCAST (Optional) - {-|detect|address[,address]...}
The broadcast address(es) for the network(s) to which the interface
belongs. For P-T-P interfaces, this column is left blank. If the
interface has multiple addresses on multiple subnets then list the
broadcast addresses as a comma-separated list.
If you use the special value detect, Shorewall will detect the
broadcast address(es) for you. If you select this option, the
interface must be up before the firewall is started.
If you don´t want to give a value for this column but you want to
enter a value in the OPTIONS column, enter - in this column.
Note to Shorewall-perl users: Shorewall-perl only supports detect
or - in this column. If you specify addresses, a compilation
warning will be issued.
OPTIONS (Optional) - [option[,option]...]
A comma-separated list of options from the following list. The
order in which you list the options is not significant but the list
should have no embedded white space.
arp_filter[={0|1}]
If specified, this interface will only respond to ARP who-has
requests for IP addresses configured on the interface. If not
specified, the interface can respond to ARP who-has requests
for IP addresses on any of the firewall´s interface. The
interface must be up when Shorewall is started.
The option value (0 or 1) may only be specified if you are
using Shorewall-perl. With Shorewall-perl, only those
interfaces with the arp_filter option will have their setting
changes; the value assigned to the setting will be the value
specified (if any) or 1 if no value is given.
Note
This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
arp_ignore[=number]
If specified, this interface will respond to arp requests based
on the value of number (defaults to 1).
1 - reply only if the target IP address is local address
configured on the incoming interface
2 - reply only if the target IP address is local address
configured on the incoming interface and the sender´s IP
address is part from same subnet on this interface
3 - do not reply for local addresses configured with scope
host, only resolutions for global and link
4-7 - reserved
8 - do not reply for all local addresses
Note
This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
Warning
Do not specify arp_ignore for any interface involved in Proxy
ARP[3].
blacklist
Check packets arriving on this interface against the
shorewall-blacklist[4](5) file.
bridge
(Shorewall-perl only) Designates the interface as a bridge.
detectnets (Deprecated and not supported by Shorewall-perl)
Automatically tailors the zone named in the ZONE column to
include only those hosts routed through the interface.
Warning
Do not set the detectnets option on your internet interface.
Support for this option will be removed in a future release of
Shorewall-perl. Better to use the routefilter option together
with the logmartians option.
dhcp
Specify this option when any of the following are true:
1. the interface gets its IP address via DHCP
2. the interface is used by a DHCP server running on the
firewall
3. the interface has a static IP but is on a LAN segment with
lots of DHCP clients.
4. the interface is a simple bridge[5] with a DHCP server on
one port and DHCP clients on another port.
Note
If you use Shorewall-perl for firewall/bridging[6], then
you need to include DHCP-specific rules in
shorewall-rules[7](8). DHCP uses UDP ports 67 and 68.
This option allows DHCP datagrams to enter and leave the
interface.
logmartians[={0|1}]
Turn on kernel martian logging (logging of packets with
impossible source addresses. It is strongly suggested that if
you set routefilter on an interface that you also set
logmartians. Even if you do not specify the routefilter option,
it is a good idea to specify logmartians because your
distribution may be enabling route filtering without you
knowing it.
The option value (0 or 1) may only be specified if you are
using Shorewall-perl. With Shorewall-perl, only those
interfaces with the logmartians option will have their setting
changes; the value assigned to the setting will be the value
specified (if any) or 1 if no value is given.
To find out if route filtering is set on a given interface,
check the contents of
/proc/sys/net/ipv4/conf/interface/rp_filter - a non-zero value
indicates that route filtering is enabled.
Example:
teastep@lists:~$ cat /proc/sys/net/ipv4/conf/eth0/rp_filter
1
teastep@lists:~$
Note
This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
This option may also be enabled globally in the
shorewall.conf[8](5) file.
maclist
Connection requests from this interface are compared against
the contents of shorewall-maclist[9](5). If this option is
specified, the interface must be an ethernet NIC and must be up
before Shorewall is started.
mss=number
Added in Shorewall 4.0.3. Causes forwarded TCP SYN packets
entering or leaving on this interface to have their MSS field
set to the specified number.
norfc1918
This interface should not receive any packets whose source is
in one of the ranges reserved by RFC 1918 (i.e., private or
"non-routable" addresses). If packet mangling or
connection-tracking match is enabled in your kernel, packets
whose destination addresses are reserved by RFC 1918 are also
rejected.
nosmurfs
Filter packets for smurfs (packets with a broadcast address as
the source).
Smurfs will be optionally logged based on the setting of
SMURF_LOG_LEVEL in shorewall.conf[8](5). After logging, the
packets are dropped.
optional
Only supported by Shorewall-perl. When optional is specified
for an interface, Shorewall will be silent when:
· a /proc/sys/net/ipv4/conf/ entry for the interface cannot
be modified (including for proxy ARP).
· The first address of the interface cannot be obtained.
I specify optional on interfaces to Xen virtual machines
that may or may not be running when Shorewall is
[re]started.
Caution
Use optional at your own risk. If you [re]start Shorewall
when an ´optional´ interface is not available and then do a
shorewall save, subsequent shorewall restore and shorewall
-f start operations will instantiate a ruleset that does
not support that interface, even if it is available at the
time of the restore/start.
proxyarp[={0|1}]
Sets /proc/sys/net/ipv4/conf/interface/proxy_arp. Do NOT use
this option if you are employing Proxy ARP through entries in
shorewall-proxyarp[10](5). This option is intended solely for
use with Proxy ARP sub-networking as described at:
http://tldp.org/HOWTO/Proxy-ARP-Subnet/index.html. [11]
Note: This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
The option value (0 or 1) may only be specified if you are
using Shorewall-perl. With Shorewall-perl, only those
interfaces with the proxyarp option will have their setting
changed; the value assigned to the setting will be the value
specified (if any) or 1 if no value is given.
routeback
If specified, indicates that Shorewall should include rules
that allow traffic arriving on this interface to be routed back
out that same interface. This option is also required when you
have used a wildcard in the INTERFACE column if you want to
allow traffic between the interfaces that match the wildcard.
routefilter[={0|1}]
Turn on kernel route filtering for this interface
(anti-spoofing measure).
The option value (0 or 1) may only be specified if you are
using Shorewall-perl. With Shorewall-perl, only those
interfaces with the routefilter option will have their setting
changes; the value assigned to the setting will be the value
specified (if any) or 1 if no value is given.
Note
This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
This option can also be enabled globally in the
shorewall.conf[8](5) file.
sourceroute[={0|1}]
If this option is not specified for an interface, then
source-routed packets will not be accepted from that interface
(sets /proc/sys/net/ipv4/conf/interface/accept_source_route to
1). Only set this option if you know what you are doing. This
might represent a security risk and is not usually needed.
The option value (0 or 1) may only be specified if you are
using Shorewall-perl. With Shorewall-perl, only those
interfaces with the sourceroute option will have their setting
changes; the value assigned to the setting will be the value
specified (if any) or 1 if no value is given.
Note
This option does not work with a wild-card interface name
(e.g., eth0.+) in the INTERFACE column.
tcpflags
Packets arriving on this interface are checked for certain
illegal combinations of TCP flags. Packets found to have such a
combination of flags are handled according to the setting of
TCP_FLAGS_DISPOSITION after having been logged according to the
setting of TCP_FLAGS_LOG_LEVEL.
upnp
Incoming requests from this interface may be remapped via UPNP
(upnpd). See http://www.shorewall.net/UPnP.html[12].
EXAMPLE
Example 1:
Suppose you have eth0 connected to a DSL modem and eth1 connected
to your local network and that your local subnet is 192.168.1.0/24.
The interface gets it´s IP address via DHCP from subnet
206.191.149.192/27. You have a DMZ with subnet 192.168.2.0/24 using
eth2.
Your entries for this setup would look like:
#ZONE INTERFACE BROADCAST OPTIONS
net eth0 206.191.149.223 dhcp
loc eth1 192.168.1.255
dmz eth2 192.168.2.255
Example 2:
The same configuration without specifying broadcast addresses is:
#ZONE INTERFACE BROADCAST OPTIONS
net eth0 detect dhcp
loc eth1 detect
dmz eth2 detect
Example 3:
You have a simple dial-in system with no ethernet connections.
#ZONE INTERFACE BROADCAST OPTIONS
net ppp0 -
FILES
/etc/shorewall/interfaces
SEE ALSOshorewall(8), shorewall-accounting(5), shorewall-actions(5),
shorewall-blacklist(5), shorewall-hosts(5), shorewall-ipsec(5),
shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5),
shorewall-netmap(5), shorewall-params(5), shorewall-policy(5),
shorewall-providers(5), shorewall-proxyarp(5),
shorewall-route_rules(5), shorewall-routestopped(5),
shorewall-rules(5), shorewall.conf(5), shorewall-tcclasses(5),
shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5),
shorewall-tunnels(5), shorewall-zones(5)NOTES
1. shorewall-hosts
shorewall-hosts.html
2. shorewall-nesting
shorewall-nesting.html
3. Proxy ARP
../ProxyARP.htm
4. shorewall-blacklist
shorewall-blacklist.html
5. simple bridge
../SimpleBridge.html
6. Shorewall-perl for firewall/bridging
../bridge-Shorewall-perl.html
7. shorewall-rules
shorewall-rules.html
8. shorewall.conf
shorewall.conf.html
9. shorewall-maclist
shorewall-maclist.html
10. shorewall-proxyarp
shorewall-proxyarp.html
11. http://tldp.org/HOWTO/Proxy-ARP-Subnet/index.html.
http://tldp.org/HOWTO/Proxy-ARP-Subnet/index.html
12. http://www.shorewall.net/UPnP.html
../UPnP.html
09/05/2009 SHOREWALL-INTERFACE(5)