socat(1)socat(1)NAMEsocat - Multipurpose relay (SOcket CAT)
SYNOPSISsocat [options] <address> <address>
socat-V
socat -h[h[h]] | -?[?[?]]
filan
procan
DESCRIPTION
Socat is a command line based utility that establishes two bidirec‐
tional byte streams and transfers data between them. Because the
streams can be constructed from a large set of different types of data
sinks and sources (see address types), and because lots of address
options may be applied to the streams, socat can be used for many dif‐
ferent purposes.
Filan is a utility that prints information about its active file
descriptors to stdout. It has been written for debugging socat, but
might be useful for other purposes too. Use the -h option to find more
infos.
Procan is a utility that prints information about process parameters to
stdout. It has been written to better understand some UNIX process
properties and for debugging socat, but might be useful for other pur‐
poses too.
The life cycle of a socat instance typically consists of four phases.
In the init phase, the command line options are parsed and logging is
initialized.
During the open phase, socat opens the first address and afterwards the
second address. These steps are usually blocking; thus, especially for
complex address types like socks, connection requests or authentication
dialogs must be completed before the next step is started.
In the transfer phase, socat watches both streams’ read and write file
descriptors via select() , and, when data is available on one side and
can be written to the other side, socat reads it, performs newline
character conversions if required, and writes the data to the write
file descriptor of the other stream, then continues waiting for more
data in both directions.
When one of the streams effectively reaches EOF, the closing phase
begins. Socat transfers the EOF condition to the other stream, i.e.
tries to shutdown only its write stream, giving it a chance to termi‐
nate gracefully. For a defined time socat continues to transfer data in
the other direction, but then closes all remaining channels and termi‐
nates.
OPTIONS
Socat provides some command line options that modify the behaviour of
the program. They have nothing to do with so called address options
that are used as parts of address specifications.
-V Print version and available feature information to stdout, and
exit.
-h | -?
Print a help text to stdout describing command line options and
available address types, and exit.
-hh | -??
Like -h, plus a list of the short names of all available address
options. Some options are platform dependend, so this output is
helpful for checking the particular implementation.
-hhh | -???
Like -hh, plus a list of all available address option names.
-d Without this option, only fatal and error messages are gener‐
ated; applying this option also prints warning messages. See
DIAGNOSTICS for more information.
-d -d Prints fatal, error, warning, and notice messages.
-d -d -d
Prints fatal, error, warning, notice, and info messages.
-d -d -d -d
Prints fatal, error, warning, notice, info, and debug messages.
-D Logs information about file descriptors before starting the
transfer phase.
-ly[<facility>]
Writes messages to syslog instead of stderr; severity as defined
with -d option. With optional <facility>, the syslog type can be
selected, default is "daemon".
-lf <logfile>
Writes messages to <logfile> [filename] instead of stderr.
-ls Writes messages to stderr (this is the default).
-lp<progname>
Overrides the program name printed in error messages and used
for constructing environment variable names.
-lu Extends the timestamp of error messages to microsecond resolu‐
tion. Does not work when logging to syslog.
-lm[<facility>]
Mixed log mode. During startup messages are printed to stderr;
when socat starts the transfer phase loop or daemon mode (i.e.
after opening all streams and before starting data transfer, or,
with listening sockets with fork option, before the first accept
call), it switches logging to syslog. With optional <facility>,
the syslog type can be selected, default is "daemon".
-lh Adds hostname to log messages. Uses the value from environment
variable HOSTNAME or the value retrieved with uname() if HOST‐
NAME is not set.
-v Writes the transferred data not only to their target streams,
but also to stderr. The output format is text with some conver‐
sions for readability, and prefixed with "> " or "< " indicating
flow directions.
-x Writes the transferred data not only to their target streams,
but also to stderr. The output format is hexadecimal, prefixed
with "> " or "< " indicating flow directions. Can be combined
with -v .
-b<size>
Sets the data transfer block <size> [size_t]. At most <size>
bytes are transferred per step. Default is 8192 bytes.
-s By default, socat terminates when an error occurred to prevent
the process from running when some option could not be applied.
With this option, socat is sloppy with errors and tries to con‐
tinue. Even with this option, socat will exit on fatals, and
will abort connection attempts when security checks failed.
-t<timeout>
When one channel has reached EOF, the write part of the other
channel is shut down. Then, socat waits <timeout> [timeval] sec‐
onds before terminating. Default is 0.5 seconds. This timeout
only applies to addresses where write and read part can be
closed independently. When during the timeout interval the read
part gives EOF, socat terminates without awaiting the timeout.
-T<timeout>
Total inactivity timeout: when socat is already in the transfer
loop and nothing has happened for <timeout> [timeval] seconds
(no data arrived, no interrupt occurred...) then it terminates.
Useful with protocols like UDP that cannot transfer EOF.
-u Uses unidirectional mode. The first address is only used for
reading, and the second address is only used for writing (exam‐
ple).
-U Uses unidirectional mode in reverse direction. The first address
is only used for writing, and the second address is only used
for reading.
-g During address option parsing, don’t check if the option is con‐
sidered useful in the given address environment. Use it if you
want to force, e.g., appliance of a socket option to a serial
device.
-L<lockfile>
If lockfile exists, exits with error. If lockfile does not
exist, creates it and continues, unlinks lockfile on exit.
-W<lockfile>
If lockfile exists, waits until it disappears. When lockfile
does not exist, creates it and continues, unlinks lockfile on
exit.
-4 Use IP version 4 in case that the addresses do not implicitly or
explicitly specify a version; this is the default.
-6 Use IP version 6 in case that the addresses do not implicitly or
explicitly specify a version.
ADDRESS SPECIFICATIONS
With the address command line arguments, the user gives socat instruc‐
tions and the necessary information for establishing the byte streams.
An address specification usually consists of an address type keyword,
zero or more required address parameters separated by ’:’ from the key‐
word and from each other, and zero or more address options separated by
’,’.
The keyword specifies the address type (e.g., TCP4, OPEN, EXEC). For
some keywords there exist synonyms (’-’ for STDIO, TCP for TCP4). Key‐
words are case insensitive. For a few special address types, the key‐
word may be omitted: Address specifications starting with a number are
assumed to be FD (raw file descriptor) addresses; if a ’/’ is found
before the first ’:’ or ’,’, GOPEN (generic file open) is assumed.
The required number and type of address parameters depend on the
address type. E.g., TCP4 requires a server specification (name or
address), and a port specification (number or service name).
Zero or more address options may be given with each address. They
influence the address in some ways. Options consist of an option key‐
word or an option keyword and a value, separated by ’=’. Option key‐
words are case insensitive. For filtering the options that are useful
with an address type, each option is member of one option group. For
each address type there is a set of option groups allowed. Only options
belonging to one of these address groups may be used (except with
option -g).
Address specifications following the above schema are also called sin‐
gle address specifications. Two single addresses can be combined with
"!!" to form a dual type address for one channel. Here, the first
address is used by socat for reading data, and the second address for
writing data. There is no way to specify an option only once for being
applied to both single addresses.
Usually, addresses are opened in read/write mode. When an address is
part of a dual address specification, or when option -u or -U is used,
an address might be used only for reading or for writing. Considering
this is important with some address types.
With socat version 1.5.0 and higher, the lexical analysis tries to han‐
dle quotes and parenthesis meaningfully and allows escaping of special
characters. If one of the characters ( { [ ’ is found, the correspond‐
ing closing character - ) } ] ’ - is looked for; they may also be
nested. Within these constructs, socats special characters and strings
: , !! are not handled specially. All those characters and strings can
be escaped with \ or within ""
ADDRESS TYPES
This section describes the available address types with their keywords,
parameters, and semantics.
CREATE:<filename>
Opens <filename> with creat() and uses the file descriptor for
writing. This address type requires write-only context, because
a file opened with creat cannot be read from.
Flags like O_LARGEFILE cannot be applied. If you need them use
OPEN with options create,create.
<filename> must be a valid existing or not existing path. If
<filename> is a named pipe, creat() might block; if <filename>
refers to a socket, this is an error.
Option groups: FD,REG,NAMED
Useful options: mode, user, group, unlink-early, unlink-late,
append
See also: OPEN, GOPEN
EXEC:<command-line>
Forks a sub process that establishes communication with its par‐
ent process and invokes the specified program with execvp() .
<command-line> is a simple command with arguments separated by
single spaces. If the program name contains a ’/’, the part
after the last ’/’ is taken as ARGV[0]. If the program name is a
relative path, the execvp() semantics for finding the program
via $PATH apply. After successful program start, socat writes
data to stdin of the process and reads from its stdout using a
UNIX domain socket generated by socketpair() per default. (exam‐
ple)
Option groups: FD,SOCKET,EXEC,FORK,TERMIOS
Useful options: path, fdin, fdout, chroot, su, su-d, nofork,
pty, stderr, ctty, setsid, pipes, login, sigint, sigquit
See also: SYSTEM
FD:<fdnum>
Uses the file descriptor <fdnum>. It must already exist as valid
UN*X file descriptor.
Option groups: FD (TERMIOS,REG,SOCKET)
See also: STDIO, STDIN, STDOUT, STDERR
GOPEN:<filename>
(Generic open) This address type tries to handle any file system
entry except directories usefully. <filename> may be a relative
or absolute path. If it already exists, its type is checked. In
case of a UNIX domain socket, socat connects; if connecting
fails, socat assumes a datagram socket and uses sendto() calls.
If the entry is not a socket, socat opens it applying the
O_APPEND flag. If it does not exist, it is opened with flag
O_CREAT as a regular file (example).
Option groups: FD,REG,SOCKET,NAMED,OPEN
See also: OPEN, CREATE, UNIX-CONNECT
IP-SENDTO:<host>:<protocol>
Opens a raw IP socket. Depending on host specification or option
pf, IP protocol version 4 or 6 is used. It uses <protocol> to
send packets to <host> [IP address] and receives packets from
host, ignores packets from other hosts. Protocol 255 uses the
raw socket with the IP header being part of the data.
Option groups: FD,SOCKET,IP4,IP6
Useful options: pf, ttl
See also: IP4-SENDTO, IP6-SENDTO, IP-RECVFROM, IP-RECV,
UDP-SENDTO, UNIX-SENDTO
INTERFACE:<interface>
Communicates with a network connected on an interface using raw
packets including link level data. <interface> is the name of
the network interface. Currently only available on Linux.
Option groups: FD,SOCKET
Useful options: pf, type
See also: ip-recv
IP4-SENDTO:<host>:<protocol>
Like IP-SENDTO, but always uses IPv4.
Option groups: FD,SOCKET,IP4
IP6-SENDTO:<host>:<protocol>
Like IP-SENDTO, but always uses IPv6.
Option groups: FD,SOCKET,IP6
IP-DATAGRAM:<address>:<protocol>
Sends outgoing data to the specified address which may in par‐
ticular be a broadcast or multicast address. Packets arriving on
the local socket are checked if their source addresses match
RANGE or TCPWRAP options. This address type can for example be
used for implementing symmetric or asymmetric broadcast or mul‐
ticast communications.
Option groups: FD, SOCKET, IP4, IP6, RANGE
Useful options: bind, range, tcpwrap, broadcast, ip-multi‐
cast-loop, ip-multicast-ttl, ip-multicast-if, ip-add-membership,
ttl, tos, pf
See also: IP4-DATAGRAM, IP6-DATAGRAM, IP-SENDTO, IP-RECVFROM,
IP-RECV, UDP-DATAGRAM
IP4-DATAGRAM:<host>:<protocol>
Like IP-DATAGRAM, but always uses IPv4. (example)
Option groups: FD,SOCKET,IP4,RANGE
IP6-DATAGRAM:<host>:<protocol>
Like IP-DATAGRAM, but always uses IPv6. Please note that IPv6
does not know broadcasts.
Option groups: FD,SOCKET,IP6,RANGE
IP-RECVFROM:<protocol>
Opens a raw IP socket of <protocol>. Depending on option pf, IP
protocol version 4 or 6 is used. It receives one packet from an
unspecified peer and may send one or more answer packets to that
peer. This mode is particularly useful with fork option where
each arriving packet - from arbitrary peers - is handled by its
own sub process. This allows a behaviour similar to typical UDP
based servers like ntpd or named.
Please note that the reply packets might be fetched as incoming
traffic when sender and receiver IP address are identical
because there is no port number to distinguish the sockets.
This address works well with IP-SENDTO address peers (see
above). Protocol 255 uses the raw socket with the IP header
being part of the data.
Option groups: FD,SOCKET,IP4,IP6,CHILD,RANGE
Useful options: pf, fork, range, ttl, broadcast
See also: IP4-RECVFROM, IP6-RECVFROM, IP-SENDTO, IP-RECV,
UDP-RECVFROM, UNIX-RECVFROM
IP4-RECVFROM:<protocol>
Like IP-RECVFROM, but always uses IPv4.
Option groups: FD,SOCKET,IP4,CHILD,RANGE
IP6-RECVFROM:<protocol>
Like IP-RECVFROM, but always uses IPv6.
Option groups: FD,SOCKET,IP6,CHILD,RANGE
IP-RECV:<protocol>
Opens a raw IP socket of <protocol>. Depending on option pf, IP
protocol version 4 or 6 is used. It receives packets from multi‐
ple unspecified peers and merges the data. No replies are pos‐
sible. It can be, e.g., addressed by socat IP-SENDTO address
peers. Protocol 255 uses the raw socket with the IP header
being part of the data.
Option groups: FD,SOCKET,IP4,IP6,RANGE
Useful options: pf, range
See also: IP4-RECV, IP6-RECV, IP-SENDTO, IP-RECVFROM, UDP-RECV,
UNIX-RECV
IP4-RECV:<protocol>
Like IP-RECV, but always uses IPv4.
Option groups: FD,SOCKET,IP4,RANGE
IP6-RECV:<protocol>
Like IP-RECV, but always uses IPv6.
Option groups: FD,SOCKET,IP6,RANGE
OPEN:<filename>
Opens <filename> using the open() system call (example). This
operation fails on UNIX domain sockets.
Note: This address type is rarly useful in bidirectional mode.
Option groups: FD,REG,NAMED,OPEN
Useful options: creat, excl, noatime, nofollow, append, rdonly,
wronly, lock, readbytes, ignoreeof
See also: CREATE, GOPEN, UNIX-CONNECT
OPENSSL:<host>:<port>
Tries to establish a SSL connection to <port> [TCP service] on
<host> [IP address] using TCP/IP version 4 or 6 depending on
address specification, name resolution, or option pf.
NOTE: The server certificate is only checked for validity
against cafile or capath, but not for match with the server’s
name or its IP address!
Option groups: FD,SOCKET,IP4,IP6,TCP,OPENSSL,RETRY
Useful options: cipher, method, verify, cafile, capath, certifi‐
cate, key, compress, bind, pf, connect-timeout, sourceport,
retry
See also: OPENSSL-LISTEN, TCP
OPENSSL-LISTEN:<port>
Listens on tcp <port> [TCP service]. The IP version is 4 or the
one specified with pf. When a connection is accepted, this
address behaves as SSL server.
Note: You probably want to use the certificate option with this
address.
NOTE: The client certificate is only checked for validity
against cafile or capath, but not for match with the client’s
name or its IP address!
Option groups: FD,SOCKET,IP4,IP6,TCP,LIS‐
TEN,OPENSSL,CHILD,RANGE,RETRY
Useful options: pf, cipher, method, verify, cafile, capath, cer‐
tificate, key, compress, fork, bind, range, tcpwrap, su, reuse‐
addr, retry
See also: OPENSSL, TCP-LISTEN
PIPE:<filename>
If <filename> already exists, it is opened. If it does not
exist, a named pipe is created and opened. Beginning with socat
version 1.4.3, the named pipe is removed when the address is
closed (but see option unlink-close
Note: When a pipe is used for both reading and writing, it works
as echo service.
Note: When a pipe is used for both reading and writing, and
socat tries to write more bytes than the pipe can buffer (Linux
2.4: 2048 bytes), socat might block. Consider using socat
option, e.g., -b 2048
Option groups: FD,NAMED,OPEN
Useful options: rdonly, nonblock, group, user, mode,
unlink-early
See also: unnamed pipe
PIPE Creates an unnamed pipe and uses it for reading and writing. It
works as an echo, because everything written to it appeares
immediately as read data.
Note: When socat tries to write more bytes than the pipe can
queue (Linux 2.4: 2048 bytes), socat might block. Consider,
e.g., using option -b 2048
Option groups: FD
See also: named pipe
PROXY:<proxy>:<hostname>:<port>
Connects to an HTTP proxy server on port 8080 using TCP/IP ver‐
sion 4 or 6 depending on address specification, name resolution,
or option pf, and sends a CONNECT request for hostname:port. If
the proxy grants access and succeeds to connect to the target,
data transfer between socat and the target can start. Note that
the traffic need not be HTTP but can be an arbitrary protocol.
Option groups: FD,SOCKET,IP4,IP6,TCP,HTTP,RETRY
Useful options: proxyport, ignorecr, proxyauth, resolve, crnl,
bind, connect-timeout, mss, sourceport, retry
See also: SOCKS, TCP
PTY Generates a pseudo terminal (pty) and uses its master side.
Another process may open the pty’s slave side using it like a
serial line or terminal. (example). If both the ptmx and the
openpty mechanisms are available, ptmx is used (POSIX).
Option groups: FD,NAMED,PTY,TERMIOS
Useful options: link, openpty, wait-slave, mode, user, group
See also: UNIX-LISTEN, PIPE, EXEC, SYSTEM
READLINE
Uses GNU readline and history on stdio to allow editing and
reusing input lines (example). This requires the GNU readline
and history libraries. Note that stdio should be a (pseudo) ter‐
minal device, otherwise readline does not seem to work.
Option groups: FD,READLINE,TERMIOS
Useful options: history, noecho
See also: STDIO
SCTP-CONNECT:<host>:<port>
Establishes an SCTP stream connection to the specified <host>
[IP address] and <port> [TCP service] using TCP/IP version 4 or
6 depending on address specification, name resolution, or option
pf.
Option groups: FD,SOCKET,IP4,IP6,SCTP,CHILD,RETRY
Useful options: bind, pf, connect-timeout, tos, mtudiscover,
sctp-maxseg, sctp-nodelay, nonblock, sourceport, retry, read‐
bytes
See also: SCTP4-CONNECT, SCTP6-CONNECT, SCTP-LISTEN, TCP-CONNECT
SCTP4-CONNECT:<host>:<port>
Like SCTP-CONNECT, but only supports IPv4 protocol.
Option groups: FD,SOCKET,IP4,SCTP,CHILD,RETRY
SCTP6-CONNECT:<host>:<port>
Like SCTP-CONNECT, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6,SCTP,CHILD,RETRY
SCTP-LISTEN:<port>
Listens on <port> [TCP service] and accepts a TCP/IP connection.
The IP version is 4 or the one specified with address option pf,
socat option (-4, -6), or environment variable
SOCAT_DEFAULT_LISTEN_IP. Note that opening this address usually
blocks until a client connects.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4,IP6,SCTP,RETRY
Useful options: crnl, fork, bind, range, tcpwrap, pf, max-chil‐
dren, backlog, sctp-maxseg, sctp-nodelay, su, reuseaddr, retry,
cool-write
See also: SCTP4-LISTEN, SCTP6-LISTEN, TCP-LISTEN, SCTP-CONNECT
SCTP4-LISTEN:<port>
Like SCTP-LISTEN, but only supports IPv4 protocol.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4,SCTP,RETRY
SCTP6-LISTEN:<port>
Like SCTP-LISTEN, but only supports IPv6 protocol.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP6,SCTP,RETRY
SOCKET-CONNECT:<domain>:<protocol>:<remote-address>
Creates a stream socket using the first and second given socket
parameters and SOCK_STREAM (see man socket\(2)) and connects to
the remote-address. The two socket parameters have to be speci‐
fied by int numbers. Consult your OS documentation and include
files to find the appropriate values. The remote-address must be
the data representation of a sockaddr structure without sa_fam‐
ily and (BSD) sa_len components.
Please note that you can - beyond the options of the specified
groups - also use options of higher level protocols when you
apply socat option -g.
Option groups: FD,SOCKET,CHILD,RETRY
Useful options: bind, setsockopt-int, setsockopt-bin, setsock‐
opt-string
See also: TCP, UDP-CONNECT, UNIX-CONNECT, SOCKET-LISTEN,
SOCKET-SENDTO
SOCKET-DATAGRAM:<domain>:<type>:<protocol>:<remote-address>
Creates a datagram socket using the first three given socket
parameters (see man socket\(2)) and sends outgoing data to the
remote-address. The three socket parameters have to be specified
by int numbers. Consult your OS documentation and include files
to find the appropriate values. The remote-address must be the
data representation of a sockaddr structure without sa_family
and (BSD) sa_len components.
Please note that you can - beyond the options of the specified
groups - also use options of higher level protocols when you
apply socat option -g.
Option groups: FD,SOCKET,RANGE
Useful options: bind, range, setsockopt-int, setsockopt-bin,
setsockopt-string
See also: UDP-DATAGRAM, IP-DATAGRAM, SOCKET-SENDTO, SOCKET-RECV,
SOCKET-RECVFROM
SOCKET-LISTEN:<domain>:<protocol>:<local-address>
Creates a stream socket using the first and second given socket
parameters and SOCK_STREAM (see man socket\(2)) and waits for
incoming connections on local-address. The two socket parameters
have to be specified by int numbers. Consult your OS documenta‐
tion and include files to find the appropriate values. The
local-address must be the data representation of a sockaddr
structure without sa_family and (BSD) sa_len components.
Please note that you can - beyond the options of the specified
groups - also use options of higher level protocols when you
apply socat option -g.
Option groups: FD,SOCKET,LISTEN,RANGE,CHILD,RETRY
Useful options: setsockopt-int, setsockopt-bin, setsock‐
opt-string
See also: TCP, UDP-CONNECT, UNIX-CONNECT, SOCKET-LISTEN,
SOCKET-SENDTO, SOCKET-SENDTO
SOCKET-RECV:<domain>:<type>:<protocol>:<local-address>
Creates a socket using the three given socket parameters (see
man socket\(2)) and binds it to <local-address>. Receives arriv‐
ing data. The three parameters have to be specified by int num‐
bers. Consult your OS documentation and include files to find
the appropriate values. The local-address must be the data rep‐
resentation of a sockaddr structure without sa_family and (BSD)
sa_len components.
Option groups: FD,SOCKET,RANGE
Useful options: range, setsockopt-int, setsockopt-bin, setsock‐
opt-string
See also: UDP-RECV, IP-RECV, UNIX-RECV, SOCKET-DATAGRAM,
SOCKET-SENDTO, SOCKET-RECVFROM
SOCKET-RECVFROM:<domain>:<type>:<protocol>:<local-address>
Creates a socket using the three given socket parameters (see
man socket\(2)) and binds it to <local-address>. Receives arriv‐
ing data and sends replies back to the sender. The first three
parameters have to be specified as int numbers. Consult your OS
documentation and include files to find the appropriate values.
The local-address must be the data representation of a sockaddr
structure without sa_family and (BSD) sa_len components.
Option groups: FD,SOCKET,CHILD,RANGE
Useful options: fork, range, setsockopt-int, setsockopt-bin,
setsockopt-string
See also: UDP-RECVFROM, IP-RECVFROM, UNIX-RECVFROM, SOCKET-DATA‐
GRAM, SOCKET-SENDTO, SOCKET-RECV
SOCKET-SENDTO:<domain>:<type>:<protocol>:<remote-address>
Creates a socket using the three given socket parameters (see
man socket\(2)). Sends outgoing data to the given address and
receives replies. The three parameters have to be specified as
int numbers. Consult your OS documentation and include files to
find the appropriate values. The remote-address must be the data
representation of a sockaddr structure without sa_family and
(BSD) sa_len components.
Option groups: FD,SOCKET
Useful options: bind, setsockopt-int, setsockopt-bin, setsock‐
opt-string
See also: UDP-SENDTO, IP-SENDTO, UNIX-SENDTO, SOCKET-DATAGRAM,
SOCKET-RECV SOCKET-RECVFROM
SOCKS4:<socks-server>:<host>:<port>
Connects via <socks-server> [IP address] to <host> [IPv4
address] on <port> [TCP service], using socks version 4 protocol
over IP version 4 or 6 depending on address specification, name
resolution, or option pf (example).
Option groups: FD,SOCKET,IP4,IP6,TCP,SOCKS4,RETRY
Useful options: socksuser, socksport, sourceport, pf, retry
See also: SOCKS4A, PROXY, TCP
SOCKS4A:<socks-server>:<host>:<port>
like SOCKS4, but uses socks protocol version 4a, thus leaving
host name resolution to the socks server.
Option groups: FD,SOCKET,IP4,IP6,TCP,SOCKS4,RETRY
STDERR Uses file descriptor 2.
Option groups: FD (TERMIOS,REG,SOCKET)
See also: FD
STDIN Uses file descriptor 0.
Option groups: FD (TERMIOS,REG,SOCKET)
Useful options: readbytes
See also: FD
STDIO Uses file descriptor 0 for reading, and 1 for writing.
Option groups: FD (TERMIOS,REG,SOCKET)
Useful options: readbytes
See also: FD
STDOUT Uses file descriptor 1.
Option groups: FD (TERMIOS,REG,SOCKET)
See also: FD
SYSTEM:<shell-command>
Forks a sub process that establishes communication with its par‐
ent process and invokes the specified program with system() .
Please note that <shell-command> [string] must not contain ’,’
or "!!", and that shell meta characters may have to be pro‐
tected. After successful program start, socat writes data to
stdin of the process and reads from its stdout.
Option groups: FD,SOCKET,EXEC,FORK,TERMIOS
Useful options: path, fdin, fdout, chroot, su, su-d, nofork,
pty, stderr, ctty, setsid, pipes, sigint, sigquit
See also: EXEC
TCP:<host>:<port>
Connects to <port> [TCP service] on <host> [IP address] using
TCP/IP version 4 or 6 depending on address specification, name
resolution, or option pf.
Option groups: FD,SOCKET,IP4,IP6,TCP,RETRY
Useful options: crnl, bind, pf, connect-timeout, tos, mtudis‐
cover, mss, nodelay, nonblock, sourceport, retry, readbytes
See also: TCP4, TCP6, TCP-LISTEN, UDP, SCTP-CONNECT, UNIX-CON‐
NECT
TCP4:<host>:<port>
Like TCP, but only supports IPv4 protocol (example).
Option groups: FD,SOCKET,IP4,TCP,RETRY
TCP6:<host>:<port>
Like TCP, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6,TCP,RETRY
TCP-LISTEN:<port>
Listens on <port> [TCP service] and accepts a TCP/IP connection.
The IP version is 4 or the one specified with address option pf,
socat option (-4, -6), or environment variable
SOCAT_DEFAULT_LISTEN_IP. Note that opening this address usually
blocks until a client connects.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4,IP6,TCP,RETRY
Useful options: crnl, fork, bind, range, tcpwrap, pf, max-chil‐
dren, backlog, mss, su, reuseaddr, retry, cool-write
See also: TCP4-LISTEN, TCP6-LISTEN, UDP-LISTEN, SCTP-LISTEN,
UNIX-LISTEN, OPENSSL-LISTEN, TCP-CONNECT
TCP4-LISTEN:<port>
Like TCP-LISTEN, but only supports IPv4 protocol (example).
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4,TCP,RETRY
TCP6-LISTEN:<port>
Like TCP-LISTEN, but only supports IPv6 protocol.
Additional useful option: ipv6only
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP6,TCP,RETRY
TUN[:<if-addr>/<bits>]
Creates a Linux TUN/TAP device and optionally assignes it the
address and netmask given by the parameters. The resulting net‐
work interface is almost ready for use by other processes; socat
serves its "wire side". This address requires read and write
access to the tunnel cloning device, usually /dev/net/tun , as
well as permission to set some ioctl()s. Option iff-up is
required to immediately activate the interface!
Option groups: FD,NAMED,OPEN,TUN
Useful options: iff-up, tun-device, tun-name, tun-type,
iff-no-pi
See also: ip-recv
UDP:<host>:<port>
Connects to <port> [UDP service] on <host> [IP address] using
UDP/IP version 4 or 6 depending on address specification, name
resolution, or option pf.
Please note that, due to UDP protocol properties, no real con‐
nection is established; data has to be sent for `connecting’ to
the server, and no end-of-file condition can be transported.
Option groups: FD,SOCKET,IP4,IP6
Useful options: ttl, tos, bind, sourceport, pf
See also: UDP4, UDP6, UDP-LISTEN, TCP, IP
UDP4:<host>:<port>
Like UDP, but only supports IPv4 protocol.
Option groups: FD,SOCKET,IP4
UDP6:<host>:<port>
Like UDP, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6
UDP-DATAGRAM:<address>:<port>
Sends outgoing data to the specified address which may in par‐
ticular be a broadcast or multicast address. Packets arriving on
the local socket are checked for the correct remote port and if
their source addresses match RANGE or TCPWRAP options. This
address type can for example be used for implementing symmetric
or asymmetric broadcast or multicast communications.
Option groups: FD,SOCKET,IP4,IP6,RANGE
Useful options: bind, range, tcpwrap, broadcast, ip-multi‐
cast-loop, ip-multicast-ttl, ip-multicast-if, ip-add-membership,
ttl, tos, sourceport, pf
See also: UDP4-DATAGRAM, UDP6-DATAGRAM, UDP-SENDTO,
UDP-RECVFROM, UDP-RECV, UDP-CONNECT, UDP-LISTEN, IP-DATAGRAM
UDP4-DATAGRAM:<address>:<port>
Like UDP-DATAGRAM, but only supports IPv4 protocol (example1,
example2).
Option groups: FD,SOCKET,IP4, RANGE
UDP6-DATAGRAM:<address>:<port>
Like UDP-DATAGRAM, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6,RANGE
UDP-LISTEN:<port>
Waits for a UDP/IP packet arriving on <port> [UDP service] and
`connects’ back to sender. The accepted IP version is 4 or the
one specified with option pf. Please note that, due to UDP pro‐
tocol properties, no real connection is established; data has to
arrive from the peer first, and no end-of-file condition can be
transported. Note that opening this address usually blocks until
a client connects.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4,IP6
Useful options: fork, bind, range, pf
See also: UDP, UDP4-LISTEN, UDP6-LISTEN, TCP-LISTEN
UDP4-LISTEN:<port>
Like UDP-LISTEN, but only support IPv4 protocol.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP4
UDP6-LISTEN:<port>
Like UDP-LISTEN, but only support IPv6 protocol.
Option groups: FD,SOCKET,LISTEN,CHILD,RANGE,IP6
UDP-SENDTO:<host>:<port>
Communicates with the specified peer socket, defined by <port>
[UDP service] on <host> [IP address], using UDP/IP version 4 or
6 depending on address specification, name resolution, or option
pf. It sends packets to and receives packets from that peer
socket only. This address effectively implements a datagram
client. It works well with socat UDP-RECVFROM and UDP-RECV
address peers.
Option groups: FD,SOCKET,IP4,IP6
Useful options: ttl, tos, bind, sourceport, pf
See also: UDP4-SENDTO, UDP6-SENDTO, UDP-RECVFROM, UDP-RECV,
UDP-CONNECT, UDP-LISTEN, IP-SENDTO
UDP4-SENDTO:<host>:<port>
Like UDP-SENDTO, but only supports IPv4 protocol.
Option groups: FD,SOCKET,IP4
UDP6-SENDTO:<host>:<port>
Like UDP-SENDTO, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6
UDP-RECVFROM:<port>
Creates a UDP socket on <port> [UDP service] using UDP/IP ver‐
sion 4 or 6 depending on option pf. It receives one packet from
an unspecified peer and may send one or more answer packets to
that peer. This mode is particularly useful with fork option
where each arriving packet - from arbitrary peers - is handled
by its own sub process. This allows a behaviour similar to typi‐
cal UDP based servers like ntpd or named. This address works
well with socat UDP-SENDTO address peers.
Option groups: FD,SOCKET,IP4,IP6,CHILD,RANGE
Useful options: fork, ttl, tos, bind, sourceport, pf
See also: UDP4-RECVFROM, UDP6-RECVFROM, UDP-SENDTO, UDP-RECV,
UDP-CONNECT, UDP-LISTEN, IP-RECVFROM, UNIX-RECVFROM
UDP4-RECVFROM:<port>
Like UDP-RECVFROM, but only supports IPv4 protocol.
Option groups: FD,SOCKET,IP4,CHILD,RANGE
UDP6-RECVFROM:<port>
Like UDP-RECVFROM, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6,CHILD,RANGE
UDP-RECV:<port>
Creates a UDP socket on <port> [UDP service] using UDP/IP ver‐
sion 4 or 6 depending on option pf. It receives packets from
multiple unspecified peers and merges the data. No replies are
possible. It works well with, e.g., socat UDP-SENDTO address
peers; it behaves similar to a syslog server.
Option groups: FD,SOCKET,IP4,IP6,RANGE
Useful options: fork, pf, bind, sourceport, ttl, tos
See also: UDP4-RECV, UDP6-RECV, UDP-SENDTO, UDP-RECVFROM,
UDP-CONNECT, UDP-LISTEN, IP-RECV, UNIX-RECV
UDP4-RECV:<port>
Like UDP-RECV, but only supports IPv4 protocol.
Option groups: FD,SOCKET,IP4,RANGE
UDP6-RECV:<port>
Like UDP-RECV, but only supports IPv6 protocol.
Option groups: FD,SOCKET,IP6,RANGE
UNIX-CONNECT:<filename>
Connects to <filename> assuming it is a UNIX domain socket. If
<filename> does not exist, this is an error; if <filename> is
not a UNIX domain socket, this is an error; if <filename> is a
UNIX domain socket, but no process is listening, this is an
error.
Option groups: FD,SOCKET,NAMED,RETRY,UNIX
) Useful options: bind
See also: UNIX-LISTEN, UNIX-SENDTO, TCP
UNIX-LISTEN:<filename>
Listens on <filename> using a UNIX domain stream socket and
accepts a connection. If <filename> exists and is not a socket,
this is an error. If <filename> exists and is a UNIX domain
socket, binding to the address fails (use option unlink-early!).
Note that opening this address usually blocks until a client
connects. Beginning with socat version 1.4.3, the file system
entry is removed when this address is closed (but see option
unlink-close) (example).
Option groups: FD,SOCKET,NAMED,LISTEN,CHILD,RETRY,UNIX
Useful options: fork, umask, mode, user, group, unlink-early
See also: UNIX-CONNECT, UNIX-RECVFROM, UNIX-RECV, TCP-LISTEN
UNIX-SENDTO:<filename>
Communicates with the specified peer socket, defined by [<file‐
name>] assuming it is a UNIX domain datagram socket. It sends
packets to and receives packets from that peer socket only.
Please note that it might be neccessary to bind the local socket
to an address (e.g. /tmp/sock1, which must not exist before).
This address type works well with socat UNIX-RECVFROM and
UNIX-RECV address peers.
Option groups: FD,SOCKET,NAMED,UNIX
Useful options: bind
See also: UNIX-RECVFROM, UNIX-RECV, UNIX-CONNECT, UDP-SENDTO,
IP-SENDTO
UNIX-RECVFROM:<filename>
Creates a UNIX domain datagram socket [<filename>]. Receives
one packet and may send one or more answer packets to that peer.
This mode is particularly useful with fork option where each
arriving packet - from arbitrary peers - is handled by its own
sub process. This address works well with socat UNIX-SENDTO
address peers.
Option groups: FD,SOCKET,NAMED,CHILD,UNIX
Useful options: fork
See also: UNIX-SENDTO, UNIX-RECV, UNIX-LISTEN, UDP-RECVFROM,
IP-RECVFROM
UNIX-RECV:<filename>
Creates a UNIX domain datagram socket [<filename>]. Receives
packets from multiple unspecified peers and merges the data. No
replies are possible. It can be, e.g., addressed by socat
UNIX-SENDTO address peers. It behaves similar to a syslog
server. Option groups: FD,SOCKET,NAMED,UNIX
See also: UNIX-SENDTO, UNIX-RECVFROM, UNIX-LISTEN, UDP-RECV,
IP-RECV
UNIX-CLIENT:<filename>
Communicates with the specified peer socket, defined by [<file‐
name>] assuming it is a UNIX domain socket. It first tries to
connect and, if that fails, assumes it is a datagram socket,
thus supporting both types.
Option groups: FD,SOCKET,NAMED,UNIX
Useful options: bind
See also: UNIX-CONNECT, UNIX-SENDTO, GOPEN
ABSTRACT-CONNECT:<string>
ABSTRACT-LISTEN:<string>
ABSTRACT-SENDTO:<string>
ABSTRACT-RECVFROM:<string>
ABSTRACT-RECV:<string>
ABSTRACT-CLIENT:<string>
The ABSTRACT addresses are almost identical to the related UNIX
addresses except that they do not address file system based
sockets but an alternate UNIX domain address space. To archieve
this the socket address strings are prefixed with "\0" inter‐
nally. This feature is available (only?) on Linux. Option
groups are the same as with the related UNIX addresses, except
that the ABSTRACT addresses are not member of the NAMED group.
ADDRESS OPTIONS
Address options can be applied to address specifications to influence
the process of opening the addresses and the properties of the result‐
ing data channels.
For technical reasons not every option can be applied to every address
type; e.g., applying a socket option to a regular file will fail. To
catch most useless combinations as early as in the open phase, the con‐
cept of option groups was introduced. Each option belongs to one or
more option groups. Options can be used only with address types that
support at least one of their option groups (but see option -g).
Address options have data types that their values must conform to.
Every address option consists of just a keyword or a keyword followed
by "=value", where value must conform to the options type. Some
address options manipulate parameters of system calls; e.g., option
sync sets the O_SYNC flag with the open() call. Other options cause a
system or library call; e.g., with option `ttl=value’ the setsock‐
opt(fd, SOL_IP, IP_TTL, value, sizeof(int)) call is applied. Other
options set internal socat variables that are used during data trans‐
fer; e.g., `crnl’ causes explicit character conversions. A few options
have more complex implementations; e.g., su-d (substuser-delayed)
inquires some user and group infos, stores them, and applies them later
after a possible chroot() call.
If multiple options are given to an address, their sequence in the
address specification has (almost) no effect on the sequence of their
execution/application. Instead, socat has built in an option phase
model that tries to bring the options in a useful order. Some options
exist in different forms (e.g., unlink, unlink-early, unlink-late) to
control the time of their execution.
If the same option is specified more than once within one address spec‐
ification, with equal or different values, the effect depends on the
kind of option. Options resulting in function calls like setsockopt()
cause multiple invocations. With options that set parameters for a
required call like open() or set internal flags, the value of the last
option occurrence is effective.
The existence or semantics of many options are system dependent. Socat
usually does NOT try to emulate missing libc or kernel features, it
just provides an interface to the underlying system. So, if an operat‐
ing system lacks a feature, the related option is simply not available
on this platform.
The following paragraphs introduce just the more common address
options. For a more comprehensive reference and to find information
about canonical option names, alias names, option phases, and platforms
see file xio.help.
FD option group
This option group contains options that are applied to a UN*X style
file descriptor, no matter how it was generated. Because all current
socat address types are file descriptor based, these options may be
applied to any address.
Note: Some of these options are also member of another option group,
that provides an other, non-fd based mechanism. For these options, it
depends on the actual address type and its option groups which mecha‐
nism is used. The second, non-fd based mechanism is prioritized.
cloexec=<bool>
Sets the FD_CLOEXEC flag with the fcntl() system call to value
<bool>. If set, the file descriptor is closed on exec() family
function calls. Socat internally handles this flag for the fds
it controls, so in most cases there will be no need to apply
this option.
setlk Tries to set a discretionary write lock to the whole file using
the fcntl(fd, F_SETLK, ...) system call. If the file is already
locked, this call results in an error. On Linux, when the file
permissions for group are "S" (g-x,g+s), and the file system is
locally mounted with the "mand" option, the lock is mandatory,
i.e. prevents other processes from opening the file.
setlkw Tries to set a discretionary waiting write lock to the whole
file using the fcntl(fd, F_SETLKW, ...) system call. If the
file is already locked, this call blocks. See option setlk for
information about making this lock mandatory.
setlk-rd
Tries to set a discretionary read lock to the whole file using
the fcntl(fd, F_SETLK, ...) system call. If the file is already
write locked, this call results in an error. See option setlk
for information about making this lock mandatory.
setlkw-rd
Tries to set a discretionary waiting read lock to the whole file
using the fcntl(fd, F_SETLKW, ...) system call. If the file is
already write locked, this call blocks. See option setlk for
information about making this lock mandatory.
flock-ex
Tries to set a blocking exclusive advisory lock to the file
using the flock(fd, LOCK_EX) system call. Socat hangs in this
call if the file is locked by another process.
flock-ex-nb
Tries to set a nonblocking exclusive advisory lock to the file
using the flock(fd, LOCK_EX|LOCK_NB) system call. If the file is
already locked, this option results in an error.
flock-sh
Tries to set a blocking shared advisory lock to the file using
the flock(fd, LOCK_SH) system call. Socat hangs in this call if
the file is locked by another process.
flock-sh-nb
Tries to set a nonblocking shared advisory lock to the file
using the flock(fd, LOCK_SH|LOCK_NB) system call. If the file is
already locked, this option results in an error.
lock Sets a blocking lock on the file. Uses the setlk or flock mecha‐
nism depending on availability on the particular platform. If
both are available, the POSIX variant (setlkw) is used.
user=<user>
Sets the <user> (owner) of the stream. If the address is member
of the NAMED option group, socat uses the chown() system call
after opening the file or binding to the UNIX domain socket
(race condition!). Without filesystem entry, socat sets the
user of the stream using the fchown() system call. These calls
might require root privilege.
user-late=<user>
Sets the owner of the fd to <user> with the fchown() system call
after opening or connecting the channel. This is useful only on
file system entries.
group=<group>
Sets the <group> of the stream. If the address is member of the
NAMED option group, socat uses the chown() system call after
opening the file or binding to the UNIX domain socket (race con‐
dition!). Without filesystem entry, socat sets the group of the
stream with the fchown() system call. These calls might require
group membership or root privilege.
group-late=<group>
Sets the group of the fd to <group> with the fchown() system
call after opening or connecting the channel. This is useful
only on file system entries.
mode=<mode>
Sets the <mode> [mode_t] (permissions) of the stream. If the
address is member of the NAMED option group and uses the open()
or creat() call, the mode is applied with these. If the address
is member of the NAMED option group without using these system
calls, socat uses the chmod() system call after opening the
filesystem entry or binding to the UNIX domain socket (race con‐
dition!). Otherwise, socat sets the mode of the stream using
fchmod() . These calls might require ownership or root privi‐
lege.
perm-late=<mode>
Sets the permissions of the fd to value <mode> [mode_t] using
the fchmod() system call after opening or connecting the chan‐
nel. This is useful only on file system entries.
append=<bool>
Always writes data to the actual end of file. If the address is
member of the OPEN option group, socat uses the O_APPEND flag
with the open() system call (example). Otherwise, socat applies
the fcntl(fd, F_SETFL, O_APPEND) call.
nonblock=<bool>
Tries to open or use file in nonblocking mode. Its only effects
are that the connect() call of TCP addresses does not block, and
that opening a named pipe for reading does not block. If the
address is member of the OPEN option group, socat uses the
O_NONBLOCK flag with the open() system call. Otherwise, socat
applies the fcntl(fd, F_SETFL, O_NONBLOCK) call.
binary Opens the file in binary mode to avoid implicit line terminator
conversions (Cygwin).
text Opens the file in text mode to force implicit line terminator
conversions (Cygwin).
noinherit
Does not keep this file open in a spawned process (Cygwin).
cool-write
Takes it easy when write fails with EPIPE or ECONNRESET and logs
the message with notice level instead of error. This prevents
the log file from being filled with useless error messages when
socat is used as a high volume server or proxy where clients
often abort the connection.
This option is experimental.
end-close
Changes the (address dependent) method of ending a connection to
just close the file descriptors. This is useful when the connec‐
tion is to be reused by or shared with other processes (exam‐
ple).
Normally, socket connections will be ended with shutdown(2)
which terminates the socket even if it is shared by multiple
processes. close(2) "unlinks" the socket from the process but
keeps it active as long as there are still links from other pro‐
cesses.
Similarly, when an address of type EXEC or SYSTEM is ended,
socat usually will explicitely kill the sub process. With this
option, it will just close the file descriptors.
shut-none
Changes the (address dependent) method of shutting down the
write part of a connection to not do anything.
shut-down
Changes the (address dependent) method of shutting down the
write part of a connection to shutdown\(fd, SHUT_WR). Is only
useful with sockets.
shut-close
Changes the (address dependent) method of shutting down the
write part of a connection to close\(fd).
shut-null
When one address indicates EOF, socat will send a zero sized
packet to the write channel of the other address to transfer the
EOF condition. This is useful with UDP and other datagram proto‐
cols. Has been tested against netcat and socat with option
null-eof.
null-eof
Normally socat will ignore empty (zero size payload) packets
arriving on datagram sockets, so it survives port scans. With
this option socat interprets empty datagram packets as EOF indi‐
cator (see shut-null).
ioctl-void=<request>
Calls ioctl() with the request value as second argument and NULL
as third argument. This option allows to utilize ioctls that are
not explicitely implemented in socat.
ioctl-int=<request>:<value>
Calls ioctl() with the request value as second argument and the
integer value as third argument.
ioctl-intp=<request>:<value>
Calls ioctl() with the request value as second argument and a
pointer to the integer value as third argument.
ioctl-bin=<request>:<value>
Calls ioctl() with the request value as second argument and a
pointer to the given data value as third argument. This data
must be specified in <dalan> form.
ioctl-string=<request>:<value>
Calls ioctl() with the request value as second argument and a
pointer to the given string as third argument. <dalan> form.
NAMED option group
These options work on file system entries.
See also options user, group, and mode.
user-early=<user>
Changes the <user> (owner) of the file system entry before
accessing it, using the chown() system call. This call might
require root privilege.
group-early=<group>
Changes the <group> of the file system entry before accessing
it, using the chown() system call. This call might require group
membership or root privilege.
perm-early=<mode>
Changes the <mode> [mode_t] of the file system entry before
accessing it, using the chmod() system call. This call might
require ownership or root privilege.
umask=<mode>
Sets the umask of the process to <mode> [mode_t] before access‐
ing the file system entry (useful with UNIX domain sockets!).
This call might affect all further operations of the socat
process!
unlink-early
Unlinks (removes) the file before opening it and even before
applying user-early etc.
unlink Unlinks (removes) the file before accessing it, but after
user-early etc.
unlink-late
Unlinks (removes) the file after opening it to make it inacces‐
sible for other processes after a short race condition.
unlink-close
Removes the addresses file system entry when closing the
address. For named pipes, listening unix domain sockets, and
the symbolic links of pty addresses, the default is 1; for cre‐
ated files, opened files, generic opened files, and client unix
domain sockets the default is 0.
OPEN option group
The OPEN group options allow to set flags with the open() system call.
E.g., option `creat’ sets the O_CREAT flag.
See also options append and nonblock.
creat=<bool>
Creates the file if it does not exist (example).
dsync=<bool>
Blocks write() calls until metainfo is physically written to
media.
excl=<bool>
With option creat, if file exists this is an error.
largefile=<bool>
On 32 bit systems, allows a file larger than 2^31 bytes.
noatime
Sets the O_NOATIME options, so reads do not change the access
timestamp.
noctty=<bool>
Does not make this file the controlling terminal.
nofollow=<bool>
Does not follow symbolic links.
nshare=<bool>
Does not allow to share this file with other processes.
rshare=<bool>
Does not allow other processes to open this file for writing.
rsync=<bool>
Blocks write() until metainfo is physically written to media.
sync=<bool>
Blocks write() until data is physically written to media.
rdonly=<bool>
Opens the file for reading only.
wronly=<bool>
Opens the file for writing only.
trunc Truncates the file to size 0 during opening it.
REG and BLK option group
These options are usually applied to a UN*X file descriptor, but their
semantics make sense only on a file supporting random access.
seek=<offset>
Applies the lseek(fd, <offset>, SEEK_SET) (or lseek64 ) system
call, thus positioning the file pointer absolutely to <offset>
[off_t or off64_t]. Please note that a missing value defaults to
1, not 0.
seek-cur=<offset>
Applies the lseek(fd, <offset>, SEEK_CUR) (or lseek64 ) system
call, thus positioning the file pointer <offset> [off_t or
off64_t] bytes relatively to its current position (which is usu‐
ally 0). Please note that a missing value defaults to 1, not 0.
seek-end=<offset>
Applies the lseek(fd, <offset>, SEEK_END) (or lseek64 ) system
call, thus positioning the file pointer <offset> [off_t or
off64_t] bytes relatively to the files current end. Please note
that a missing value defaults to 1, not 0.
ftruncate=<offset>
Applies the ftruncate(fd, <offset>) (or ftruncate64 if avail‐
able) system call, thus truncating the file at the position
<offset> [off_t or off64_t]. Please note that a missing value
defaults to 1, not 0.
secrm=<bool>
unrm=<bool>
compr=<bool>
ext2-sync=<bool>
immutable=<bool>
ext2-append=<bool>
nodump=<bool>
ext2-noatime=<bool>
journal-data=<bool>
notail=<bool>
dirsync=<bool>
These options change non standard file attributes on operating
systems and file systems that support these features, like Linux
with ext2fs, ext3fs, or reiserfs. See man 1 chattr for informa‐
tion on these options. Please note that there might be a race
condition between creating the file and applying these options.
PROCESS option group
Options of this group change the process properties instead of just
affecting one data channel. For EXEC and SYSTEM addresses and for LIS‐
TEN and CONNECT type addresses with option FORK, these options apply to
the child processes instead of the main socat process.
chroot=<directory>
Performs a chroot() operation to <directory> after processing
the address (example). This call might require root privilege.
chroot-early=<directory>
Performs a chroot() operation to <directory> before opening the
address. This call might require root privilege.
setgid=<group>
Changes the primary <group> of the process after processing the
address. This call might require root privilege. Please note
that this option does not drop other group related privileges.
setgid-early=<group>
Like setgit but is performed before opening the address.
setuid=<user>
Changes the <user> (owner) of the process after processing the
address. This call might require root privilege. Please note
that this option does not drop group related privileges. Check
if option su better fits your needs.
setuid-early=<user>
Like setuid but is performed before opening the address.
su=<user>
Changes the <user> (owner) and groups of the process after pro‐
cessing the address (example). This call might require root
privilege.
su-d=<user>
Short name for substuser-delayed. Changes the <user> (owner)
and groups of the process after processing the address (exam‐
ple). The user and his groups are retrieved before a possible
chroot() . This call might require root privilege.
setpgid=<pid_t>
Makes the process a member of the specified process group
<pid_t>. If no value is given, or if the value is 0 or 1, the
process becomes leader of a new process group.
setsid Makes the process the leader of a new session (example).
READLINE option group
These options apply to the readline address type.
history=<filename>
Reads and writes history from/to <filename> (example).
noprompt
Since version 1.4.0, socat per default tries to determine a
prompt - that is then passed to the readline call - by remember‐
ing the last incomplete line of the output. With this option,
socat does not pass a prompt to readline, so it begins line
editing in the first column of the terminal.
noecho=<pattern>
Specifies a regular pattern for a prompt that prevents the fol‐
lowing input line from being displayed on the screen and from
being added to the history. The prompt is defined as the text
that was output to the readline address after the lastest new‐
line character and before an input character was typed. The pat‐
tern is a regular expression, e.g. "^[Pp]assword:.*$" or
"([Uu]ser:|[Pp]assword:)". See regex\(7) for details. (example)
prompt=<string>
Passes the string as prompt to the readline function. readline
prints this prompt when stepping through the history. If this
string matches a constant prompt issued by an interactive pro‐
gram on the other socat address, consistent look and feel can be
archieved.
APPLICATION option group
This group contains options that work at data level. Note that these
options only apply to the "raw" data transferred by socat, but not to
protocol data used by addresses like PROXY.
cr Converts the default line termination character NL (’\n’, 0x0a)
to/from CR (’\r’, 0x0d) when writing/reading on this channel.
crnl Converts the default line termination character NL (’\n’, 0x0a)
to/from CRNL ("\r\n", 0x0d0a) when writing/reading on this chan‐
nel (example). Note: socat simply strips all CR characters.
ignoreeof
When EOF occurs on this channel, socat ignores it and tries to
read more data (like "tail -f") (example).
readbytes=<bytes>
socat reads only so many bytes from this address (the address
provides only so many bytes for transfer and pretends to be at
EOF afterwards). Must be greater than 0.
lockfile=<filename>
If lockfile exists, exits with error. If lockfile does not
exist, creates it and continues, unlinks lockfile on exit.
waitlock=<filename>
If lockfile exists, waits until it disappears. When lockfile
does not exist, creates it and continues, unlinks lockfile on
exit.
escape=<int>
Specifies the numeric code of a character that triggers EOF on
the input stream. It is useful with a terminal in raw mode
(example).
SOCKET option group
These options are intended for all kinds of sockets, e.g. IP or UNIX
domain. Most are applied with a setsockopt() call.
bind=<sockname>
Binds the socket to the given socket address using the bind()
system call. The form of <sockname> is socket domain dependent:
IP4 and IP6 allow the form [hostname|hostaddress][:(ser‐
vice|port)] (example), UNIX domain sockets require <filename>.
connect-timeout=<seconds>
Abort the connection attempt after <seconds> [timeval] with
error status.
so-bindtodevice=<interface>
Binds the socket to the given <interface>. This option might
require root privilege.
broadcast
For datagram sockets, allows sending to broadcast addresses and
receiving packets addressed to broadcast addresses.
debug Enables socket debugging.
dontroute
Only communicates with directly connected peers, does not use
routers.
keepalive
Enables sending keepalives on the socket.
linger=<seconds>
Blocks shutdown() or close() until data transfers have finished
or the given timeout [int] expired.
oobinline
Places out-of-band data in the input data stream.
priority=<priority>
Sets the protocol defined <priority> [<int>] for outgoing pack‐
ets.
rcvbuf=<bytes>
Sets the size of the receive buffer after the socket() call to
<bytes> [int]. With TCP sockets, this value corresponds to the
socket’s maximal window size.
rcvbuf-late=<bytes>
Sets the size of the receive buffer when the socket is already
connected to <bytes> [int]. With TCP sockets, this value corre‐
sponds to the socket’s maximal window size.
rcvlowat=<bytes>
Specifies the minimum number of received bytes [int] until the
socket layer will pass the buffered data to socat.
rcvtimeo=<seconds>
Sets the receive timeout [timeval].
reuseaddr
Allows other sockets to bind to an address even if parts of it
(e.g. the local port) are already in use by socat (example).
sndbuf=<bytes>
Sets the size of the send buffer after the socket() call to
<bytes> [int].
sndbuf-late=<bytes>
Sets the size of the send buffer when the socket is connected to
<bytes> [int].
sndlowat=<bytes>
Specifies the minimum number of bytes in the send buffer until
the socket layer will send the data to <bytes> [int].
sndtimeo=<seconds>
Sets the send timeout to seconds [timeval].
pf=<string>
Forces the use of the specified IP version or protocol. <string>
can be something like "ip4" or "ip6". The resulting value is
used as first argument to the socket() or socketpair() calls.
This option affects address resolution and the required syntax
of bind and range options.
type=<type>
Sets the type of the socket, specified as second argument to the
socket() or socketpair() calls, to <type> [int]. Address resolu‐
tion is not affected by this option. Under Linux, 1 means
stream oriented socket, 2 means datagram socket, and 3 means raw
socket.
prototype
Sets the protocol of the socket, specified as third argument to
the socket() or socketpair() calls, to <prototype> [int].
Address resolution is not affected by this option. 6 means TCP,
17 means UDP.
so-timestamp
Sets the SO_TIMESTAMP socket option. This enables receiving and
logging of timestamp ancillary messages.
setsockopt-int=<level>:<optname>:<optval>
Invokes setsockopt() for the socket with the given parameters.
level [int] is used as second argument to setsockopt() and spec‐
ifies the layer, e.g. SOL_TCP for TCP (6 on Linux), or
SOL_SOCKET for the socket layer (1 on Linux). optname [int] is
the third argument to setsockopt() and tells which socket option
is to be set. For the actual numbers you might have to look up
the appropriate include files of your system. The 4th setsock‐
opt() parameter, value [int], is passed to the function per
pointer, and for the length parameter sizeof\(int) is taken
implicitely.
setsockopt-bin=<level>:<optname>:<optval>
Like setsockopt-int, but <optval> must be provided in dalan for‐
mat and specifies an arbitrary sequence of bytes; the length
parameter is automatically derived from the data.
setsockopt-string=<level>:<optname>:<optval>
Like setsockopt-int, but <optval> must be a string. This string
is passed to the function with trailing null character, and the
length parameter is automatically derived from the data.
UNIX option group
These options apply to UNIX domain based addresses.
unix-tightsocklen=[0|1]
On socket operations, pass a socket address length that does not
include the whole struct sockaddr_un record but (besides other
components) only the relevant part of the filename or abstract
string. Default is 1.
IP4 and IP6 option groups
These options can be used with IPv4 and IPv6 based sockets.
tos=<tos>
Sets the TOS (type of service) field of outgoing packets to
<tos> [byte] (see RFC 791).
ttl=<ttl>
Sets the TTL (time to live) field of outgoing packets to <ttl>
[byte].
ip-options=<data>
Sets IP options like source routing. Must be given in binary
form, recommended format is a leading "x" followed by an even
number of hex digits. This option may be used multiple times,
data are appended. E.g., to connect to host 10.0.0.1 via some
gateway using a loose source route, use the gateway as address
parameter and set a loose source route using the option
ip-options=x8307040a000001 .
IP options are defined in RFC 791.
mtudiscover=<0|1|2>
Takes 0, 1, 2 to never, want, or always use path MTU discover on
this socket.
ip-pktinfo
Sets the IP_PKTINFO socket option. This enables receiving and
logging of ancillary messages containing destination address and
interface (Linux) (example).
ip-recverr
Sets the IP_RECVERR socket option. This enables receiving and
logging of ancillary messages containing detailled error infor‐
mation.
ip-recvopts
Sets the IP_RECVOPTS socket option. This enables receiving and
logging of IP options ancillary messages (Linux, *BSD).
ip-recvtos
Sets the IP_RECVTOS socket option. This enables receiving and
logging of TOS (type of service) ancillary messages (Linux).
ip-recvttl
Sets the IP_RECVTTL socket option. This enables receiving and
logging of TTL (time to live) ancillary messages (Linux, *BSD).
ip-recvdstaddr
Sets the IP_RECVDSTADDR socket option. This enables receiving
and logging of ancillary messages containing destination address
(*BSD) (example).
ip-recvif
Sets the IP_RECVIF socket option. This enables receiving and
logging of interface ancillary messages (*BSD) (example).
ip-add-membership=<multicast-address:interface-address>
ip-add-membership=<multicast-address:interface-name>
ip-add-membership=<multicast-address:interface-index>
ip-add-membership=<multicast-address:interface-address:interface-name>
ip-add-membership=<multicast-address:interface-address:interface-index>
Makes the socket member of the specified multicast group. This
is currently only implemented for IPv4. The option takes the IP
address of the multicast group and info about the desired net‐
work interface. The most common syntax is the first one, while
the others are only available on systems that provide struct
mreqn (Linux).
The indices of active network interfaces can be shown using the
utility procan.
ip-multicast-if=<hostname>
Specifies hostname or address of the network interface to be
used for multicast traffic.
ip-multicast-loop=<bool>
Specifies if outgoing multicast traffic should loop back to the
interface.
ip-multicast-ttl=<byte>
Sets the TTL used for outgoing multicast traffic. Default is 1.
res-debug
res-aaonly
res-usevc
res-primary
res-igntc
res-recurse
res-defnames
res-stayopen
res-dnsrch
These options set the corresponding resolver (name resolution)
option flags. Append "=0" to clear a default option. See man
resolver\(5) for more information on these options. Note: these
options are valid only for the address they are applied to.
IP6 option group
These options can only be used on IPv6 based sockets. See IP options
for options that can be applied to both IPv4 and IPv6 sockets.
ipv6only=<bool>
Sets the IPV6_V6ONLY socket option. If 0, the TCP stack will
also accept connections using IPv4 protocol on the same port.
The default is system dependent.
ipv6-recvdstopts
Sets the IPV6_RECVDSTOPTS socket option. This enables receiving
and logging of ancillary messages containing the destination
options.
ipv6-recvhoplimit
Sets the IPV6_RECVHOPLIMIT socket option. This enables receiving
and logging of ancillary messages containing the hoplimit.
ipv6-recvhopopts
Sets the IPV6_RECVHOPOPTS socket option. This enables receiving
and logging of ancillary messages containing the hop options.
ipv6-recvpktinfo
Sets the IPV6_RECVPKTINFO socket option. This enables receiving
and logging of ancillary messages containing destination address
and interface.
ipv6-unicast-hops=link(TYPE_INT)(<int>)
Sets the IPV6_UNICAST_HOPS socket option. This sets the hop
count limit (TTL) for outgoing unicast packets.
ipv6-recvrthdr
Sets the IPV6_RECVRTHDR socket option. This enables receiving
and logging of ancillary messages containing routing informa‐
tion.
ipv6-tclass
Sets the IPV6_TCLASS socket option. This sets the transfer class
of outgoing packets.
ipv6-recvtclass
Sets the IPV6_RECVTCLASS socket option. This enables receiving
and logging of ancillary messages containing the transfer class.
TCP option group
These options may be applied to TCP sockets. They work by invoking set‐
sockopt() with the appropriate parameters.
cork Doesn’t send packets smaller than MSS (maximal segment size).
defer-accept
While listening, accepts connections only when data from the
peer arrived.
keepcnt=<count>
Sets the number of keepalives before shutting down the socket to
<count> [int].
keepidle=<seconds>
Sets the idle time before sending the first keepalive to <sec‐
onds> [int].
keepintvl=<seconds>
Sets the interval between two keepalives to <seconds> [int].
linger2=<seconds>
Sets the time to keep the socket in FIN-WAIT-2 state to <sec‐
onds> [int].
mss=<bytes>
Sets the MSS (maximum segment size) after the socket() call to
<bytes> [int]. This value is then proposed to the peer with the
SYN or SYN/ACK packet (example).
mss-late=<bytes>
Sets the MSS of the socket after connection has been established
to <bytes> [int].
nodelay
Turns off the Nagle algorithm for measuring the RTT (round trip
time).
rfc1323
Enables RFC1323 TCP options: TCP window scale, round-trip time
measurement (RTTM), and protect against wrapped sequence numbers
(PAWS) (AIX).
stdurg Enables RFC1122 compliant urgent pointer handling (AIX).
syncnt=<count>
Sets the maximal number of SYN retransmits during connect to
<count> [int].
md5sig Enables generation of MD5 digests on the packets (FreeBSD).
noopt Disables use of TCP options (FreeBSD, MacOSX).
nopush sets the TCP_NOPUSH socket option (FreeBSD, MacOSX).
sack-disable
Disables use the selective acknowledge feature (OpenBSD).
signature-enable
Enables generation of MD5 digests on the packets (OpenBSD).
abort-threshold=<milliseconds>
Sets the time to wait for an answer of the peer on an estab‐
lished connection (HP-UX).
conn-abort-threshold=<milliseconds>
Sets the time to wait for an answer of the server during the
initial connect (HP-UX).
keepinit
Sets the time to wait for an answer of the server during con‐
nect\() before giving up. Value in half seconds, default is 150
(75s) (Tru64).
paws Enables the "protect against wrapped sequence numbers" feature
(Tru64).
sackena
Enables selective acknowledge (Tru64).
tsoptena
Enables the time stamp option that allows RTT recalculation on
existing connections (Tru64).
SCTP option group
These options may be applied to SCTP stream sockets.
sctp-nodelay
Sets the SCTP_NODELAY socket option that disables the Nagle
algorithm.
sctp-maxseg=<bytes>
Sets the SCTP_MAXSEG socket option to <bytes> [int]. This value
is then proposed to the peer with the SYN or SYN/ACK packet.
UDP, TCP, and SCTP option groups
Here we find options that are related to the network port mechanism and
thus can be used with UDP, TCP, and SCTP client and server addresses.
sourceport=<port>
For outgoing (client) TCP and UDP connections, it sets the
source <port> using an extra bind() call. With TCP or UDP lis‐
ten addresses, socat immediately shuts down the connection if
the client does not use this sourceport (example).
lowport
Outgoing (client) TCP and UDP connections with this option use
an unused random source port between 640 and 1023 incl. On UNIX
class operating systems, this requires root privilege, and thus
indicates that the client process is authorized by local root.
TCP and UDP listen addresses with this option immediately shut
down the connection if the client does not use a sourceport <=
1023. This mechanism can provide limited authorization under
some circumstances.
SOCKS option group
When using SOCKS type addresses, some socks specific options can be
set.
socksport=<tcp service>
Overrides the default "socks" service or port 1080 for the socks
server port with <TCP service>.
socksuser=<user>
Sends the <user> [string] in the username field to the socks
server. Default is the actual user name ($LOGNAME or $USER)
(example).
HTTP option group
Options that can be provided with HTTP type addresses. The only HTTP
address currently implemented is proxy-connect.
proxyport=<TCP service>
Overrides the default HTTP proxy port 8080 with <TCP service>.
ignorecr
The HTTP protocol requires the use of CR+NL as line terminator.
When a proxy server violates this standard, socat might not
understand its answer. This option directs socat to interprete
NL as line terminator and to ignore CR in the answer. Neverthe‐
less, socat sends CR+NL to the proxy.
proxyauth=<username>:<password>
Provide "basic" authentication to the proxy server. The argument
to the option is used with a "Proxy-Authorization: Base" header
in base64 encoded form.
Note: username and password are visible for every user on the
local machine in the process list; username and password are
transferred to the proxy server unencrypted (base64 encoded) and
might be sniffed.
resolve
Per default, socat sends to the proxy a CONNECT request contain‐
ing the target hostname. With this option, socat resolves the
hostname locally and sends the IP address. Please note that,
according to RFC 2396, only name resolution to IPv4 addresses is
implemented.
RANGE option group
These options check if a connecting client should be granted access.
They can be applied to listening and receiving network sockets.
tcp-wrappers options fall into this group.
range=<address-range>
After accepting a connection, tests if the peer is within range.
For IPv4 addresses, address-range takes the form address/bits,
e.g. 10.0.0.0/8, or address:mask, e.g. 10.0.0.0:255.0.0.0
(example); for IPv6, it is [ip6-address/bits], e.g. [::1/128].
If the client address does not match, socat issues a warning and
keeps listening/receiving.
tcpwrap[=<name>]
Uses Wietse Venema’s libwrap (tcpd) library to determine if the
client is allowed to connect. The configuration files are
/etc/hosts.allow and /etc/hosts.deny per default, see "man 5
hosts_access" for more information. The optional <name> (type
string) is passed to the wrapper functions as daemon process
name (example). If omitted, the basename of socats invocation
(argv[0]) is passed. If both tcpwrap and range options are
applied to an address, both conditions must be fulfilled to
allow the connection.
allow-table=<filename>
Takes the specified file instead of /etc/hosts.allow.
deny-table=<filename>
Takes the specified file instead of /etc/hosts.deny.
tcpwrap-etc=<directoryname>
Looks for hosts.allow and hosts.deny in the specified directory.
Is overridden by options hosts-allow and hosts-deny.
LISTEN option group
Options specific to listening sockets.
backlog=<count>
Sets the backlog value passed with the listen() system call to
<count> [int]. Default is 5.
max-children=<count>
Limits the number of concurrent child processes [int]. Default
is no limit.
CHILD option group
Options for addresses with multiple connections via child processes.
fork After establishing a connection, handles its channel in a child
process and keeps the parent process attempting to produce more
connections, either by listening or by connecting in a loop
(example).
SSL-CONNECT and SSL-LISTEN differ in when they actually fork off
the child: SSL-LISTEN forks before the SSL handshake, while
SSL-CONNECT forks afterwards. RETRY and FOREVER options are not
inherited by the child process.
EXEC option group
Options for addresses that invoke a program.
path=<string>
Overrides the PATH environment variable for searching the pro‐
gram with <string>. This $PATH value is effective in the child
process too.
login Prefixes argv[0] for the execvp() call with ’-’, thus making a
shell behave as login shell.
FORK option group
EXEC or SYSTEM addresses invoke a program using a child process and
transfer data between socat and the program. The interprocess communi‐
cation mechanism can be influenced with the following options. Per
default, a socketpair() is created and assigned to stdin and stdout of
the child process, while stderr is inherited from the socat process,
and the child process uses file descriptors 0 and 1 for communicating
with the main socat process.
nofork Does not fork a subprocess for executing the program, instead
calls execvp\() or system\() directly from the actual socat
instance. This avoids the overhead of another process between
the program and its peer, but introduces a lot of restrictions:
o this option can only be applied to the second socat address.
o it cannot be applied to a part of a dual address.
o the first socat address cannot be OPENSSL or READLINE
o socat options -b, -t, -D, -l, -v, -x become useless
o for both addresses, options ignoreeof, cr, and crnl become use‐
less
o for the second address (the one with option nofork), options
append, cloexec, flock, user, group, mode, nonblock, perm-late,
setlk, and setpgid cannot be applied. Some of these could be
used on the first address though.
pipes Creates a pair of unnamed pipes for interprocess communication
instead of a socket pair.
openpty
Establishes communication with the sub process using a pseudo
terminal created with openpty() instead of the default (socket‐
pair or ptmx).
ptmx Establishes communication with the sub process using a pseudo
terminal created by opening /dev/ptmx or /dev/ptc instead of the
default (socketpair).
pty Establishes communication with the sub process using a pseudo
terminal instead of a socket pair. Creates the pty with an
available mechanism. If openpty and ptmx are both available, it
uses ptmx because this is POSIX compliant (example).
ctty Makes the pty the controlling tty of the sub process (example).
stderr Directs stderr of the sub process to its output channel by mak‐
ing stderr a dup() of stdout (example).
fdin=<fdnum>
Assigns the sub processes input channel to its file descriptor
<fdnum> instead of stdin (0). The program started from the sub‐
process has to use this fd for reading data from socat (exam‐
ple).
fdout=<fdnum>
Assigns the sub processes output channel to its file descriptor
<fdnum> instead of stdout (1). The program started from the sub‐
process has to use this fd for writing data to socat (example).
sighup, sigint, sigquit
Has socat pass signals of this type to the sub process. If no
address has this option, socat terminates on these signals.
TERMIOS option group
For addresses that work on a tty (e.g., stdio, file:/dev/tty,
exec:...,pty), the terminal parameters defined in the UN*X termios
mechanism are made available as address option parameters. Please note
that changes of the parameters of your interactive terminal remain
effective after socat’s termination, so you might have to enter "reset"
or "stty sane" in your shell afterwards. For EXEC and SYSTEM addresses
with option PTY, these options apply to the pty by the child processes.
b0 Disconnects the terminal.
b19200 Sets the serial line speed to 19200 baud. Some other rates are
possible; use something like socat-hh |grep ’ b[1-9]’ to find
all speeds supported by your implementation.
Note: On some operating systems, these options may not be avail‐
able. Use ispeed or ospeed instead.
echo=<bool>
Enables or disables local echo (example).
icanon=<bool>
Sets or clears canonical mode, enabling line buffering and some
special characters.
raw Sets raw mode, thus passing input and output almost unprocessed
(example).
ignbrk=<bool>
Ignores or interpretes the BREAK character (e.g., ^C)
brkint=<bool>
bs0
bs1
bsdly=<0|1>
clocal=<bool>
cr0
cr1
cr2
cr3
Sets the carriage return delay to 0, 1, 2, or 3, respectively.
0 means no delay, the other values are terminal dependent.
crdly=<0|1|2|3>
cread=<bool>
crtscts=<bool>
cs5
cs6
cs7
cs8
Sets the character size to 5, 6, 7, or 8 bits, respectively.
csize=<0|1|2|3>
cstopb=<bool>
Sets two stop bits, rather than one.
dsusp=<byte>
Sets the value for the VDSUSP character that suspends the cur‐
rent foreground process and reactivates the shell (all except
Linux).
echoctl=<bool>
Echos control characters in hat notation (e.g. ^A)
echoe=<bool>
echok=<bool>
echoke=<bool>
echonl=<bool>
echoprt=<bool>
eof=<byte>
eol=<byte>
eol2=<byte>
erase=<byte>
discard=<byte>
ff0
ff1
ffdly=<bool>
flusho=<bool>
hupcl=<bool>
icrnl=<bool>
iexten=<bool>
igncr=<bool>
ignpar=<bool>
imaxbel=<bool>
inlcr=<bool>
inpck=<bool>
intr=<byte>
isig=<bool>
ispeed=<unsigned-int>
Set the baud rate for incoming data on this line.
See also: ospeed, b19200
istrip=<bool>
iuclc=<bool>
ixany=<bool>
ixoff=<bool>
ixon=<bool>
kill=<byte>
lnext=<byte>
min=<byte>
nl0 Sets the newline delay to 0.
nl1
nldly=<bool>
noflsh=<bool>
ocrnl=<bool>
ofdel=<bool>
ofill=<bool>
olcuc=<bool>
onlcr=<bool>
onlret=<bool>
onocr=<bool>
opost=<bool>
Enables or disables output processing; e.g., converts NL to
CR-NL.
ospeed=<unsigned-int>
Set the baud rate for outgoing data on this line.
See also: ispeed, b19200
parenb=<bool>
Enable parity generation on output and parity checking for
input.
parmrk=<bool>
parodd=<bool>
pendin=<bool>
quit=<byte>
reprint=<byte>
sane Brings the terminal to something like a useful default state.
start=<byte>
stop=<byte>
susp=<byte>
swtc=<byte>
tab0
tab1
tab2
tab3
tabdly=<unsigned-int>
time=<byte>
tostop=<bool>
vt0
vt1
vtdly=<bool>
werase=<byte>
xcase=<bool>
xtabs
i-pop-all
With UNIX System V STREAMS, removes all drivers from the stack.
i-push=<string>
With UNIX System V STREAMS, pushes the driver (module) with the
given name (string) onto the stack. For example, to make sure
that a character device on Solaris supports termios etc, use the
following options:
i-pop-all,i-push=ptem,i-push=ldterm,i-push=ttcompat
PTY option group
These options are intended for use with the pty address type.
link=<filename>
Generates a symbolic link that points to the actual pseudo ter‐
minal (pty). This might help to solve the problem that ptys are
generated with more or less unpredictable names, making it dif‐
ficult to directly access the socat generated pty automatically.
With this option, the user can specify a "fix" point in the file
hierarchy that helps him to access the actual pty (example).
Beginning with socat version 1.4.3, the symbolic link is removed
when the address is closed (but see option unlink-close).
wait-slave
Blocks the open phase until a process opens the slave side of
the pty. Usually, socat continues after generating the pty with
opening the next address or with entering the transfer loop.
With the wait-slave option, socat waits until some process opens
the slave side of the pty before continuing. This option only
works if the operating system provides the poll() system call.
And it depends on an undocumented behaviour of pty’s, so it does
not work on all operating systems. It has successfully been
tested on Linux, FreeBSD, NetBSD, and on Tru64 with openpty.
pty-interval=<seconds>
When the wait-slave option is set, socat periodically checks the
HUP condition using poll() to find if the pty’s slave side has
been opened. The default polling interval is 1s. Use the
pty-interval option [timeval] to change this value.
OPENSSL option group
These options apply to the openssl and openssl-listen address types.
cipher=<cipherlist>
Selects the list of ciphers that may be used for the connection.
See the man page of ciphers , section CIPHER LIST FORMAT, for
detailed information about syntax, values, and default of
<cipherlist>.
Several cipher strings may be given, separated by ’:’. Some
simple cipher strings:
3DES Uses a cipher suite with triple DES.
MD5 Uses a cipher suite with MD5.
aNULL Uses a cipher suite without authentication.
NULL Does not use encryption.
HIGH Uses a cipher suite with "high" encryption. Note that the peer
must support the selected property, or the negotiation will
fail.
method=<ssl-method>
Sets the protocol version to be used. Valid strings (not case
sensitive) are:
SSLv2 Select SSL protocol version 2.
SSLv3 Select SSL protocol version 3.
SSLv23 Select SSL protocol version 2 or 3. This is the default when
this option is not provided.
TLSv1 Select TLS protocol version 1.
verify=<bool>
Controls check of the peer’s certificate. Default is 1 (true).
Disabling verify might open your socket for everyone, making the
encryption useless!
cert=<filename>
Specifies the file with the certificate and private key for
authentication. The certificate must be in OpenSSL format
(*.pem). With openssl-listen, use of this option is strongly
recommended. Except with cipher aNULL, "no shared ciphers" error
will occur when no certificate is given.
key=<filename>
Specifies the file with the private key. The private key may be
in this file or in the file given with the cert option. The
party that has to proof that it is the owner of a certificate
needs the private key.
dhparams=<filename>
Specifies the file with the Diffie Hellman parameters. These
parameters may also be in the file given with the cert option in
which case the dhparams option is not needed.
cafile=<filename>
Specifies the file with the trusted (root) authority certifi‐
cates. The file must be in PEM format and should contain one or
more certificates. The party that checks the authentication of
its peer trusts only certificates that are in this file.
capath=<dirname>
Specifies the directory with the trusted (root) certificates.
The directory must contain certificates in PEM format and their
hashes (see OpenSSL documentation)
egd=<filename>
On some systems, openssl requires an explicit source of random
data. Specify the socket name where an entropy gathering daemon
like egd provides random data, e.g. /dev/egd-pool.
pseudo On systems where openssl cannot find an entropy source and where
no entropy gathering daemon can be utilized, this option acti‐
vates a mechanism for providing pseudo entropy. This is
archieved by taking the current time in microseconds for feeding
the libc pseudo random number generator with an initial value.
openssl is then feeded with output from random\() calls.
NOTE:This mechanism is not sufficient for generation of secure
keys!
compress
Enable or disable the use of compression for a connection. Set‐
ting this to "none" disables compression, setting it to "auto"
lets OpenSSL choose the best available algorithm supported by
both parties. The default is to not touch any compres‐
sion-related settings. NOTE: Requires OpenSSL 0.9.8 or higher
and disabling compression with OpenSSL 0.9.8 affects all new
connections in the process.
fips Enables FIPS mode if compiled in. For info about the FIPS
encryption implementation standard see http://oss-insti‐
tute.org/fips-faq.html. This mode might require that the
involved certificates are generated with a FIPS enabled version
of openssl. Setting or clearing this option on one socat address
affects all OpenSSL addresses of this process.
RETRY option group
Options that control retry of some system calls, especially connection
attempts.
retry=<num>
Number of retries before the connection or listen attempt is
aborted. Default is 0, which means just one attempt.
interval=<timespec>
Time between consecutive attempts (seconds, [timespec]). Default
is 1 second.
forever
Performs an unlimited number of retry attempts.
TUN option group
Options that control Linux TUN/TAP interface device addresses.
tun-device=<device-file>
Instructs socat to take another path for the TUN clone device.
Default is /dev/net/tun.
tun-name=<if-name>
Gives the resulting network interface a specific name instead of
the system generated (tun0, tun1, etc.)
tun-type=[tun|tap]
Sets the type of the TUN device; use this option to generate a
TAP device. See the Linux docu for the difference between these
types. When you try to establish a tunnel between two TUN
devices, their types should be the same.
iff-no-pi
Sets the IFF_NO_PI flag which controls if the device includes
additional packet information in the tunnel. When you try to
establish a tunnel between two TUN devices, these flags should
have the same values.
iff-up Sets the TUN network interface status UP. Strongly recommended.
iff-broadcast
Sets the BROADCAST flag of the TUN network interface.
iff-debug
Sets the DEBUG flag of the TUN network interface.
iff-loopback
Sets the LOOPBACK flag of the TUN network interface.
iff-pointopoint
Sets the POINTOPOINT flag of the TUN device.
iff-notrailers
Sets the NOTRAILERS flag of the TUN device.
iff-running
Sets the RUNNING flag of the TUN device.
iff-noarp
Sets the NOARP flag of the TUN device.
iff-promisc
Sets the PROMISC flag of the TUN device.
iff-allmulti
Sets the ALLMULTI flag of the TUN device.
iff-master
Sets the MASTER flag of the TUN device.
iff-slave
Sets the SLAVE flag of the TUN device.
iff-multicast
Sets the MULTICAST flag of the TUN device.
iff-portsel
Sets the PORTSEL flag of the TUN device.
iff-automedia
Sets the AUTOMEDIA flag of the TUN device.
iff-dynamic
Sets the DYNAMIC flag of the TUN device.
DATA VALUES
This section explains the different data types that address parameters
and address options can take.
address-range
Is currently only implemented for IPv4 and IPv6. See
address-option `range’
bool "0" or "1"; if value is omitted, "1" is taken.
byte An unsigned int number, read with strtoul() , lower or equal to
UCHAR_MAX .
command-line
A string specifying a program name and its arguments, separated
by single spaces.
data A raw data specification following dalan syntax. Currently the
only valid form is a string starting with ’x’ followed by an
even number of hex digits, specifying a sequence of bytes.
directory
A string with usual UN*X directory name semantics.
facility
The name of a syslog facility in lower case characters.
fdnum An unsigned int type, read with strtoul() , specifying a UN*X
file descriptor.
filename
A string with usual UN*X filename semantics.
group If the first character is a decimal digit, the value is read
with strtoul() as unsigned integer specifying a group id. Other‐
wise, it must be an existing group name.
int A number following the rules of the strtol() function with base
"0", i.e. decimal number, octal number with leading "0", or
hexadecimal number with leading "0x". The value must fit into a
C int.
interface
A string specifying the device name of a network interface as
shown by ifconfig or procan, e.g. "eth0".
IP address
An IPv4 address in numbers-and-dots notation, an IPv6 address in
hex notation enclosed in brackets, or a hostname that resolves
to an IPv4 or an IPv6 address.
Examples: 127.0.0.1, [::1], www.dest-unreach.org, dns1
IPv4 address
An IPv4 address in numbers-and-dots notation or a hostname that
resolves to an IPv4 address.
Examples: 127.0.0.1, www.dest-unreach.org, dns2
IPv6 address
An iPv6 address in hexnumbers-and-colons notation enclosed in
brackets, or a hostname that resolves to an IPv6 address.
Examples: [::1], [1234:5678:9abc:def0:1234:5678:9abc:def0],
ip6name.domain.org
long A number read with strtol() . The value must fit into a C long.
long long
A number read with strtoll() . The value must fit into a C long
long.
off_t An implementation dependend signed number, usually 32 bits, read
with strtol or strtoll.
off64_t
An implementation dependend signed number, usually 64 bits, read
with strtol or strtoll.
mode_t An unsigned integer, read with strtoul() , specifying mode (per‐
mission) bits.
pid_t A number, read with strtol() , specifying a process id.
port A uint16_t (16 bit unsigned number) specifying a TCP or UDP
port, read with strtoul() .
protocol
An unsigned 8 bit number, read with strtoul() .
size_t An unsigned number with size_t limitations, read with strtoul .
sockname
A socket address. See address-option `bind’
string A sequence of characters, not containing ’\0’ and, depending on
the position within the command line, ’:’, ’,’, or "!!". Note
that you might have to escape shell meta characters in the com‐
mand line.
TCP service
A service name, not starting with a digit, that is resolved by
getservbyname() , or an unsigned int 16 bit number read with
strtoul() .
timeval
A double float specifying seconds; the number is mapped into a
struct timeval, consisting of seconds and microseconds.
timespec
A double float specifying seconds; the number is mapped into a
struct timespec, consisting of seconds and nanoseconds.
UDP service
A service name, not starting with a digit, that is resolved by
getservbyname() , or an unsigned int 16 bit number read with
strtoul() .
unsigned int
A number read with strtoul() . The value must fit into a C
unsigned int.
user If the first character is a decimal digit, the value is read
with strtoul() as unsigned integer specifying a user id. Other‐
wise, it must be an existing user name.
EXAMPLESsocat - TCP4:www.domain.org:80
transfers data between STDIO (-) and a TCP4 connection to port
80 of host www.domain.org. This example results in an interac‐
tive connection similar to telnet or netcat. The stdin terminal
parameters are not changed, so you may close the relay with ^D
or abort it with ^C.
socat-d -d READLINE,history=$HOME/.http_history \
TCP4:www.domain.org:www,crnl
this is similar to the previous example, but you can edit the
current line in a bash like manner (READLINE) and use the his‐
tory file .http_history; socat prints messages about progress
(-d -d). The port is specified by service name (www), and cor‐
rect network line termination characters (crnl) instead of NL
are used.
socat TCP4-LISTEN:www TCP4:www.domain.org:www
installs a simple TCP port forwarder. With TCP4-LISTEN it lis‐
tens on local port "www" until a connection comes in, accepts
it, then connects to the remote host (TCP4) and starts data
transfer. It will not accept a econd connection.
socat-d -d -lmlocal2 \
TCP4-LISTEN:80,bind=myaddr1,reuseaddr,fork,su=nobody,range=10.0.0.0/8 \
TCP4:www.domain.org:80,bind=myaddr2
TCP port forwarder, each side bound to another local IP address
(bind). This example handles an almost arbitrary number of par‐
allel or consecutive connections by fork’ing a new process after
each accept() . It provides a little security by su’ing to user
nobody after forking; it only permits connections from the pri‐
vate 10 network (range); due to reuseaddr, it allows immediate
restart after master process’s termination, even if some child
sockets are not completely shut down. With -lmlocal2, socat
logs to stderr until successfully reaching the accept loop. Fur‐
ther logging is directed to syslog with facility local2.
socat TCP4-LISTEN:5555,fork,tcpwrap=script \
EXEC:/bin/myscript,chroot=/home/sandbox,su-d=sandbox,pty,stderr
a simple server that accepts connections (TCP4-LISTEN) and
fork’s a new child process for each connection; every child acts
as single relay. The client must match the rules for daemon
process name "script" in /etc/hosts.allow and /etc/hosts.deny,
otherwise it is refused access (see "man 5 hosts_access"). For
EXEC’uting the program, the child process chroot’s to
/home/sandbox, su’s to user sandbox, and then starts the program
/home/sandbox/bin/myscript. Socat and myscript communicate via a
pseudo tty (pty); myscript’s stderr is redirected to stdout, so
its error messages are transferred via socat to the connected
client.
socat EXEC:"mail.sh target@domain.com",fdin=3,fdout=4 \
TCP4:mail.relay.org:25,crnl,bind=alias1.server.org,mss=512
mail.sh is a shell script, distributed with socat, that imple‐
ments a simple SMTP client. It is programmed to "speak" SMTP on
its FDs 3 (in) and 4 (out). The fdin and fdout options tell
socat to use these FDs for communication with the program.
Because mail.sh inherits stdin and stdout while socat does not
use them, the script can read a mail body from stdin. Socat
makes alias1 your local source address (bind), cares for correct
network line termination (crnl) and sends at most 512 data bytes
per packet (mss).
socat -,raw,echo=0,escape=0x0f /dev/ttyS0,raw,echo=0,crnl
opens an interactive connection via the serial line, e.g. for
talking with a modem. raw and echo set the console’s and ttyS0’s
terminal parameters to practicable values, crnl converts to cor‐
rect newline characters. escape allows to terminate the socat
process with character control-O. Consider using READLINE
instead of the first address.
socat UNIX-LISTEN:/tmp/.X11-unix/X1,fork \
SOCKS4:host.victim.org:127.0.0.1:6000,socksuser=nobody,sourceport=20
with UNIX-LISTEN, socat opens a listening UNIX domain socket
/tmp/.X11-unix/X1. This path corresponds to local XWindow dis‐
play :1 on your machine, so XWindow client connections to DIS‐
PLAY=:1 are accepted. Socat then speaks with the SOCKS4 server
host.victim.org that might permit sourceport 20 based connec‐
tions due to an FTP related weakness in its static IP filters.
Socat pretends to be invoked by socksuser nobody, and requests
to be connected to loopback port 6000 (only weak sockd configu‐
rations will allow this). So we get a connection to the victims
XWindow server and, if it does not require MIT cookies or Ker‐
beros authentication, we can start work. Please note that there
can only be one connection at a time, because TCP can establish
only one session with a given set of addresses and ports.
socat-u /tmp/readdata,seek-end=0,ignoreeof -
this is an example for unidirectional data transfer (-u). Socat
transfers data from file /tmp/readdata (implicit address GOPEN),
starting at its current end (seek-end=0 lets socat start reading
at current end of file; use seek=0 or no seek option to first
read the existing data) in a "tail -f" like mode (ignoreeof).
The "file" might also be a listening UNIX domain socket (do not
use a seek option then).
(sleep 5; echo PASSWORD; sleep 5; echo ls; sleep 1) |
socat - EXEC:'ssh -l user server',pty,setsid,ctty
EXEC’utes an ssh session to server. Uses a pty for communication
between socat and ssh, makes it ssh’s controlling tty (ctty),
and makes this pty the owner of a new process group (setsid), so
ssh accepts the password from socat.
socat-u TCP4-LISTEN:3334,reuseaddr,fork \
OPEN:/tmp/in.log,creat,append
implements a simple network based message collector. For each
client connecting to port 3334, a new child process is generated
(option fork). All data sent by the clients are append’ed to
the file /tmp/in.log. If the file does not exist, socat creat’s
it. Option reuseaddr allows immediate restart of the server
process.
socat READLINE,noecho=’[Pp]assword:’ EXEC:’ftp ftp.server.com’,pty,set‐
sid,ctty
wraps a command line history (READLINE) around the EXEC’uted ftp
client utility. This allows editing and reuse of FTP commands
for relatively comfortable browsing through the ftp directory
hierarchy. The password is echoed! pty is required to have ftp
issue a prompt. Nevertheless, there may occur some confusion
with the password and FTP prompts.
(socat PTY,link=$HOME/dev/vmodem0,raw,echo=0,wait-slave
EXEC:’"ssh modemserver.us.org socat - /dev/ttyS0,non‐
block,raw,echo=0"’)
generates a pseudo terminal device (PTY) on the client that can
be reached under the symbolic link $HOME/dev/vmodem0. An appli‐
cation that expects a serial line or modem can be configured to
use $HOME/dev/vmodem0; its traffic will be directed to a modem‐
server via ssh where another socat instance links it with
/dev/ttyS0.
socat TCP4-LISTEN:2022,reuseaddr,fork \
PROXY:proxy:www.domain.org:22,proxyport=3128,proxyauth=user:pass
starts a forwarder that accepts connections on port 2022, and
directs them through the proxy daemon listening on port 3128
(proxyport) on host proxy, using the CONNECT method, where they
are authenticated as "user" with "pass" (proxyauth). The proxy
should establish connections to host www.domain.org on port 22
then.
socat - SSL:server:4443,cafile=server.crt,cert=client.pem
is an OpenSSL client that tries to establish a secure connection
to an SSL server. Option cafile specifies a file that contains
trust certificates: we trust the server only when it presents
one of these certificates and proofs that it owns the related
private key. Otherwise the connection is terminated. With cert
a file containing the client certificate and the associated pri‐
vate key is specified. This is required in case the server
wishes a client authentication; many Internet servers do not.
The first address (’-’) can be replaced by almost any other
socat address.
socat SSL-LISTEN:4443,reuse‐
addr,pf=ip4,fork,cert=server.pem,cafile=client.crt PIPE
is an OpenSSL server that accepts TCP connections, presents the
certificate from the file server.pem and forces the client to
present a certificate that is verified against cafile.crt.
The second address (’PIPE’) can be replaced by almost any other
socat address.
For instructions on generating and distributing OpenSSL keys and
certificates see the additional socat docu socat-openssl.txt.
echo |socat -u - file:/tmp/bigfile,create,largefile,seek=100000000000
creates a 100GB sparse file; this requires a file system type
that supports this (ext2, ext3, reiserfs, jfs; not minix, vfat).
The operation of writing 1 byte might take long (reiserfs: some
minutes; ext2: "no" time), and the resulting file can consume
some disk space with just its inodes (reiserfs: 2MB; ext2:
16KB).
socat tcp-l:7777,reuseaddr,fork system:’filan -i 0 -s >&2’,nofork
listens for incoming TCP connections on port 7777. For each
accepted connection, invokes a shell. This shell has its stdin
and stdout directly connected to the TCP socket (nofork). The
shell starts filan and lets it print the socket addresses to
stderr (your terminal window).
echo -e "\0\14\0\0\c" |socat -u-
file:/usr/bin/squid.exe,seek=0x00074420
functions as primitive binary editor: it writes the 4 bytes 000
014 000 000 to the executable /usr/bin/squid at offset
0x00074420 (this is a real world patch to make the squid exe‐
cutable from Cygwin run under Windows, actual per May 2004).
socat - tcp:www.blackhat.org:31337,readbytes=1000
connects to an unknown service and prevents being flooded.
socat-U TCP:target:9999,end-close TCP-L:8888,reuseaddr,fork
merges data arriving from different TCP streams on port 8888 to
just one stream to target:9999. The end-close option prevents
the child processes forked off by the second address from termi‐
nating the shared connection to 9999 (close\(2) just unlinks the
inode which stays active as long as the parent process lives;
shutdown\(2) would actively terminate the connection).
socat - UDP4-DATAGRAM:192.168.1.0:123,sp=123,broad‐
cast,range=192.168.1.0/24
sends a broadcast to the network 192.168.1.0/24 and receives the
replies of the timeservers there. Ignores NTP packets from hosts
outside this network.
socat - SOCKET-DATA‐
GRAM:2:2:17:x007bxc0a80100x0000000000000000,bind=x007bx00000000x0000000000000000,set‐
sock‐
opt-int=1:6:1,range=x0000xc0a80100x0000000000000000:x0000xffffff00x0000000000000000
is semantically equivalent to the previous example, but all
parameters are specified in generic form. the value 6 of set‐
sockopt-int is the Linux value for SO_BROADCAST.
socat - IP4-DATAGRAM:255.255.255.255:44,broadcast,range=10.0.0.0/8
sends a broadcast to the local network\(s) using protocol 44.
Accepts replies from the private address range only.
socat - UDP4-DATAGRAM:224.255.0.1:6666,bind=:6666,ip-add-member‐
ship=224.255.0.1:eth0
transfers data from stdin to the specified multicast address
using UDP. Both local and remote ports are 6666. Tells the
interface eth0 to also accept multicast packets of the given
group. Multiple hosts on the local network can run this command,
so all data sent by any of the hosts will be received by all the
other ones. Note that there are many possible reasons for fail‐
ure, including IP-filters, routing issues, wrong interface
selection by the operating system, bridges, or a badly config‐
ured switch.
socat TCP:host2:4443 TUN:192.168.255.1/24,up
establishes one side of a virtual (but not private!) network
with host2 where a similar process might run, with UDP-L and tun
address 192.168.255.2. They can reach each other using the
addresses 192.168.255.1 and 192.168.255.2. Note that streaming
eg. via TCP or SSL does not guarantee to retain packet bound‐
aries and may thus cause packet loss.
socat PTY,link=/var/run/ppp,raw,echo=0 INTERFACE:hdlc0
circumvents the problem that pppd requires a serial device and
thus might not be able to work on a synchronous line that is
represented by a network device. socat creates a PTY to make
pppd happy, binds to the network interface hdlc0, and can trans‐
fer data between both devices. Use pppd on device /var/run/ppp
then.
socat-T 1 -d-d TCP-L:10081,reuseaddr,fork,crlf SYSTEM:"echo -e
\"\\\"HTTP/1.0 200 OK\\\nDocumentType: text/plain\\\n\\\ndate:
\$\(date\)\\\nserver:\$SOCAT_SOCKADDR:\$SOCAT_SOCKPORT\\\nclient:
\$SOCAT_PEERADDR:\$SOCAT_PEERPORT\\\n\\\"\"; cat; echo -e
\"\\\"\\\n\\\"\""
creates a simple HTTP echo server: each HTTP client that con‐
nects gets a valid HTTP reply that contains information about
the client address and port as it is seen by the server host,
the host address (which might vary on multihomed servers), and
the original client request.
socat-d-d UDP4-RECVFROM:9999,so-broadcast,so-timestamp,ip-pkt‐
info,ip-recverr,ip-recvopts,ip-recvtos,ip-recvttl!!- SYSTEM:’export;
sleep 1’ |grep SOCAT
waits for an incoming UDP packet on port 9999 and prints the
environment variables provided by socat. On BSD based systems
you have to replace ip-pktinfo with ip-recvdstaddr,ip-recvif.
Especially interesting is SOCAT_IP_DSTADDR: it contains the tar‐
get address of the packet which may be a unicast, multicast, or
broadcast address.
DIAGNOSTICS
Socat uses a logging mechanism that allows to filter messages by sever‐
ity. The severities provided are more or less compatible to the appro‐
priate syslog priority. With one or up to four occurrences of the -d
command line option, the lowest priority of messages that are issued
can be selected. Each message contains a single uppercase character
specifying the messages severity (one of F, E, W, N, I, or D)
FATAL: Conditions that require unconditional and immediate program ter‐
mination.
ERROR: Conditions that prevent proper program processing. Usually the
program is terminated (see option -s).
WARNING:
Something did not function correctly or is in a state where cor‐
rect further processing cannot be guaranteed, but might be pos‐
sible.
NOTICE:
Interesting actions of the program, e.g. for supervising socat
in some kind of server mode.
INFO: Description of what the program does, and maybe why it happens.
Allows to monitor the lifecycles of file descriptors.
DEBUG: Description of how the program works, all system or library
calls and their results.
Log messages can be written to stderr, to a file, or to syslog.
On exit, socat gives status 0 if it terminated due to EOF or inactivity
timeout, with a positive value on error, and with a negative value on
fatal error.
FILES
/usr/bin/socat
/usr/bin/filan
/usr/bin/procan
ENVIRONMENT VARIABLES
Input variables carry information from the environment to socat, output
variables are set by socat for use in executed scripts and programs.
In the output variables beginning with "SOCAT" this prefix is actually
replaced by the upper case name of the executable or the value of
option -lp.
SOCAT_DEFAULT_LISTEN_IP (input)
(Values 4 or 6) Sets the IP version to be used for listen, recv,
and recvfrom addresses if no pf (protocol-family) option is
given. Is overridden by socat options -4 or -6.
SOCAT_PREFERRED_RESOLVE_IP (input)
(Values 0, 4, or 6) Sets the IP version to be used when resolv‐
ing target host names when version is not specified by address
type, option pf (protocol-family), or address format. If name
resolution does not return a matching entry, the first result
(with differing IP version) is taken. With value 0, socat always
selects the first record and its IP version.
SOCAT_FORK_WAIT (input)
Specifies the time (seconds) to sleep the parent and child pro‐
cesses after successful fork\(). Useful for debugging.
SOCAT_VERSION (output)
Socat sets this variable to its version string, e.g. "1.7.0.0"
for released versions or e.g. "1.6.0.1+envvar" for temporary
versions; can be used in scripts invoked by socat.
SOCAT_PID (output)
Socat sets this variable to its process id. In case of fork
address option, SOCAT_PID gets the child processes id. Forking
for exec and system does not change SOCAT_PID.
SOCAT_PPID (output)
Socat sets this variable to its process id. In case of fork,
SOCAT_PPID keeps the pid of the master process.
SOCAT_PEERADDR (output)
With passive socket addresses (all LISTEN and RECVFROM
addresses), this variable is set to a string describing the
peers socket address. Port information is not included.
SOCAT_PEERPORT (output)
With appropriate passive socket addresses (TCP, UDP, and SCTP -
LISTEN and RECVFROM), this variable is set to a string contain‐
ing the number of the peer port.
SOCAT_SOCKADDR (output)
With all LISTEN addresses, this variable is set to a string
describing the local socket address. Port information is not
included example
SOCAT_SOCKPORT (output)
With TCP-LISTEN, UDP-LISTEN, and SCTP-LISTEN addresses, this
variable is set to the local port.
SOCAT_TIMESTAMP (output)
With all RECVFROM addresses where address option so-timestamp is
applied, socat sets this variable to the resulting timestamp.
SOCAT_IP_OPTIONS (output)
With all IPv4 based RECVFROM addresses where address option
ip-recvopts is applied, socat fills this variable with the IP
options of the received packet.
SOCAT_IP_DSTADDR (output)
With all IPv4 based RECVFROM addresses where address option
ip-recvdstaddr (BSD) or ip-pktinfo (other platforms) is applied,
socat sets this variable to the destination address of the
received packet. This is particularly useful to identify broad‐
cast and multicast addressed packets.
SOCAT_IP_IF (output)
With all IPv4 based RECVFROM addresses where address option
ip-recvif (BSD) or ip-pktinfo (other platforms) is applied,
socat sets this variable to the name of the interface where the
packet was received.
SOCAT_IP_LOCADDR (output)
With all IPv4 based RECVFROM addresses where address option
ip-pktinfo is applied, socat sets this variable to the address
of the interface where the packet was received.
SOCAT_IP_TOS (output)
With all IPv4 based RECVFROM addresses where address option
ip-recvtos is applied, socat sets this variable to the TOS (type
of service) of the received packet.
SOCAT_IP_TTL (output)
With all IPv4 based RECVFROM addresses where address option
ip-recvttl is applied, socat sets this variable to the TTL (time
to live) of the received packet.
SOCAT_IPV6_HOPLIMIT (output)
With all IPv6 based RECVFROM addresses where address option
ipv6-recvhoplimit is applied, socat sets this variable to the
hoplimit value of the received packet.
SOCAT_IPV6_DSTADDR (output)
With all IPv6 based RECVFROM addresses where address option
ipv6-recvpktinfo is applied, socat sets this variable to the
destination address of the received packet.
SOCAT_IPV6_TCLASS (output)
With all IPv6 based RECVFROM addresses where address option
ipv6-recvtclass is applied, socat sets this variable to the
transfer class of the received packet.
HOSTNAME (input)
Is used to determine the hostname for logging (see -lh).
LOGNAME (input)
Is used as name for the socks client user name if no socksuser
is given.
With options su and su-d, LOGNAME is set to the given user name.
USER (input)
Is used as name for the socks client user name if no socksuser
is given and LOGNAME is empty.
With options su and su-d, USER is set to the given user name.
SHELL (output)
With options su and su-d, SHELL is set to the login shell of the
given user.
PATH (output)
Can be set with option path for exec and system addresses.
HOME (output)
With options su and su-d, HOME is set to the home directory of
the given user.
CREDITS
The work of the following groups and organizations was invaluable for
this project:
The FSF (GNU, http://www.fsf.org/ project with their free and portable
development software and lots of other useful tools and libraries.
The Linux developers community (http://www.linux.org/) for providing a
free, open source operating system.
The Open Group (http://www.unix-systems.org/) for making their standard
specifications available on the Internet for free.
VERSION
This man page describes version 1.7.2 of socat.
BUGS
Addresses cannot be nested, so a single socat process cannot, e.g.,
drive ssl over socks.
Address option ftruncate without value uses default 1 instead of 0.
Verbose modes (-x and/or -v) display line termination characters incon‐
sistently when address options cr or crnl are used: They show the data
after conversion in either direction.
The data transfer blocksize setting (-b) is ignored with address read‐
line.
Send bug reports to <socat@dest-unreach.org>
SEE ALSO
nc\(1), netcat6\(1), sock\(1), rinetd\(8), cage\(1), socks.conf\(5),
openssl\(1), stunnel\(8), pty\(1), rlwrap\(1), setsid\(1)
Socat home page http://www.dest-unreach.org/socat/
AUTHOR
Gerhard Rieger <rieger@dest-unreach.org>
Dec 2011 socat(1)
