tcptrack(1)tcptrack(1)NAMEtcptrack - Monitor TCP connections on the network
SYNOPSIStcptrack [ -dfhvp ] [ -r seconds ] -i interface
[ filter expression ]
DESCRIPTIONtcptrack displays the status of TCP connections that it sees on a given
network interface. tcptrack monitors their state and displays informa‐
tion such as state, source/destination addresses and bandwidth usage in
a sorted, updated list very much like the top(1) command.
The filter expression is a standard pcap filter expression (identical
to the expressions used by tcpdump(8)) which can be used to filter down
the characteristics of TCP connections that tcptrack will see. See tcp‐
dump(8) for more information about the syntax of this expression.
OPTIONS-d Only track connections that were started after tcptrack was
started. Do not try to detect existing connections.
-f Enable fast average recalculation. TCPTrack will calculate the
average speeds of connections by using a running average. TCP‐
Track will use more memory and CPU time, but averages will seem
closer to real time and will be updated more than once per sec‐
ond and may be more accurate under heavy load. The number of
times per second that averages will be recalculated in fast mode
is a compile-time setting that defaults to 10 times per second.
-h Display command line help
-i [interface]
Sniff packets from the specified network interface.
-T [pcap file]
Read packets from the specified file instead of sniffing from
the network. Useful for testing.
-p Do not put the interface being sniffed into promiscuous mode.
-r [seconds]
Wait this many seconds before removing a closed connection from
the display. Defaults to 2 seconds. See also the pause interac‐
tive command (below).
-v Display tcptrack version
INTERACTIVE COMMANDS
The following keys may be pressed while tcptrack is running to change
runtime options:
p - Pause/unpause display. No new connections will be added to the dis‐
play, and all currently displayed connections will remain in the dis‐
play.
q - Quit tcptrack.
s - Cycle through the sorting options: unsorted, sorted by rate, sorted
by total bytes.
The options for pausing and toggling sorting are useful if you're
watching a very busy network and want to look at the display without
connections jumping around (due to sorting and new connections being
added) and disappearing (due to being closed for a certain time).
When paused (via the p command) no new connections will be displayed,
however tcptrack will still monitor and track all connections it sees
as usual. This option affects the display only, not internals. When you
unpause, the display will be updated with all current information that
tcptrack has been gathering all along.
EXAMPLEStcptrack requires only one parameter to run: the -i flag followed by an
interface name that you want tcptrack to monitor. This is the most
basic way to run tcptrack:
# tcptrack-i eth0
tcptrack can also take a pcap filter expression as an argument. The
format of this filter expression is the same as that of tcpdump(8) and
other libpcap-based sniffers. The following example will only show con‐
nections from host 10.45.165.2:
# tcptrack-i eth0 src or dst 10.45.165.2
The next example will only show web traffic (ie, traffic on port 80):
# tcptrack-i eth0 port 80
SEE ALSOtcpdump(8), pcap(3), http://www.rhythm.cx/~steve/devel/tcptrack
BUGS
When picking up a connection that was already running before tcptrack
was started, there is no way tcptrack can know for sure which end of
the connection is the client (ie, which peer started the connection)
and which is the server (ie, which peer was listening). tcptrack makes
a crude guess at which is which by looking at the port numbers; which‐
ever end has the lower port number is considered the server side. This
isn't always accurate of course, but future versions may have better
heuristics to figure out which end is which.
Currently the interface is not very flexible. Display timing settings
(such as the refresh interval) can only be changed by editing the
source code (defs.h in particular). See the TODO file included with the
source distribution for further bugs.
tcptrack(1)
